<![CDATA[SoliForum - 3D Printing Community — repetier issue]]> https://www.soliforum.com/topic/12278/repetier-issue/ Sun, 13 Sep 2015 16:49:18 +0000 PunBB <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105346/#p105346 And you were right, just for the noise part, it worth the upgrade.... it also look like it unleashed Simplify 3D too...

]]> Sun, 13 Sep 2015 16:49:18 +0000 https://www.soliforum.com/post/105346/#p105346 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105343/#p105343 I know!, it's just before I set to table 5, I was able to get the PETG to stick, now with table 5 active the initial temp seems right but I need to figure out the correct temp for this filament...

]]> Sun, 13 Sep 2015 16:17:06 +0000 https://www.soliforum.com/post/105343/#p105343 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105319/#p105319 You need to use glue stick or hairspray on the bed. The system will not home at the start of a print unless you add the command to do so to your start gcode.

]]> Sun, 13 Sep 2015 02:22:20 +0000 https://www.soliforum.com/post/105319/#p105319 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105318/#p105318 now the frikkin stuff won't stick to the bed...

]]> Sun, 13 Sep 2015 02:07:04 +0000 https://www.soliforum.com/post/105318/#p105318 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105315/#p105315 ok i think i got it... now need to learn how the bitch behave... is it normal behavior that you have to home all before each print? I'm using S3D and usually at start the bed is down and work from there... now if I start a print with the bed down, the print will start but the bed will stay down...

]]> Sun, 13 Sep 2015 01:14:01 +0000 https://www.soliforum.com/post/105315/#p105315 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105309/#p105309 Arduino: 1.5.8 (Windows 8), Board: "Arduino Due (Native USB Port)"

Sketch uses 158,156 bytes (30%) of program storage space. Maximum is 524,288 bytes.

processing.app.debug.RunnerException: Couldn't find a Board on the selected port. Check that you have the correct port selected.  If it is correct, try pressing the board's reset button after initiating the upload.

    at cc.arduino.packages.uploaders.SerialUploader.waitForUploadPort(SerialUploader.java:199)

    at cc.arduino.packages.uploaders.SerialUploader.uploadUsingPreferences(SerialUploader.java:95)

    at processing.app.Sketch.upload(Sketch.java:1713)

    at processing.app.Sketch.exportApplet(Sketch.java:1624)

    at processing.app.Sketch.exportApplet(Sketch.java:1596)

    at processing.app.Editor$DefaultExportHandler.run(Editor.java:2392)

    at java.lang.Thread.run(Unknown Source)

Couldn't find a Board on the selected port. Check that you have the correct port selected.  If it is correct, try pressing the board's reset button after initiating the upload.

  This report would have more information with
  "Show verbose output during compilation"
  enabled in File > Preferences.

]]> Sun, 13 Sep 2015 00:29:53 +0000 https://www.soliforum.com/post/105309/#p105309 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105305/#p105305 when I try this, it give me an error concerning the com port...

]]> Sun, 13 Sep 2015 00:22:09 +0000 https://www.soliforum.com/post/105305/#p105305 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105304/#p105304 icebob wrote:

so I will need to short j37 again right?

No, once the firmware is installed the machine is seen differently. All you need to do is make sure no programs are open using the machine. Then open the folder  for your firmware and double click the file Repetier.INO. It should open in Arduino. Make your changes and then upload. That is all there is to it. That jumper shorting was a one time thing to erase the stock firmware which makes the machine be seen in a different way from Repetier. Stock firmware used a different communication setup.

]]> Sun, 13 Sep 2015 00:20:31 +0000 https://www.soliforum.com/post/105304/#p105304 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105303/#p105303 so I will need to short j37 again right?

]]> Sun, 13 Sep 2015 00:12:33 +0000 https://www.soliforum.com/post/105303/#p105303 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105302/#p105302 icebob wrote:

ok is there a way just to set it back to 5 without reflashing the whole thing?

Nope, you have to flash. Once it has been done once it is as easy as turning the machine on.

]]> Sun, 13 Sep 2015 00:01:48 +0000 https://www.soliforum.com/post/105302/#p105302 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105301/#p105301 ok is there a way just to set it back to 5 without reflashing the whole thing?

]]> Sat, 12 Sep 2015 23:49:38 +0000 https://www.soliforum.com/post/105301/#p105301 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105300/#p105300 It should still be 5 to my knowledge. The issue is the Da Vinci has a resistor on the main board that changes the value of the thermistor. However both the stock and E3D hotends use the same standard 100K thermistor.

]]> Sat, 12 Sep 2015 23:47:06 +0000 https://www.soliforum.com/post/105300/#p105300 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105299/#p105299 not stock extruder E3D V6

]]> Sat, 12 Sep 2015 23:39:00 +0000 https://www.soliforum.com/post/105299/#p105299 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105298/#p105298 It should be 5 with a stock extruder.

]]> Sat, 12 Sep 2015 23:31:40 +0000 https://www.soliforum.com/post/105298/#p105298 <![CDATA[Re: repetier issue]]> https://www.soliforum.com/post/105295/#p105295 I put the 8 in config.h before flashing... i think default was 5...

]]> Sat, 12 Sep 2015 22:58:39 +0000 https://www.soliforum.com/post/105295/#p105295