<![CDATA[SoliForum - 3D Printing Community — Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/topic/12118/da-vinci-10a-repetier-host-e3d-v6-bowden-retraction/ Mon, 31 Aug 2015 18:03:27 +0000 PunBB <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104562/#p104562 kev0175 wrote:
DopeSkrit wrote:
kev0175 wrote:

I just wanted to make sure but in your fan on the E3D hooked up to a 12v supply?

Its hooked up to the 3D printers power supply to the 12 V rail.

OK, also is the fan well ventilated. When I first did mine it wasn't getting enough air and was clicking even trying to print abs

I printed a new carrage. It isnt very well ventilated...

]]> Mon, 31 Aug 2015 18:03:27 +0000 https://www.soliforum.com/post/104562/#p104562 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104557/#p104557 DopeSkrit wrote:
kev0175 wrote:

I just wanted to make sure but in your fan on the E3D hooked up to a 12v supply?

Its hooked up to the 3D printers power supply to the 12 V rail.

OK, also is the fan well ventilated. When I first did mine it wasn't getting enough air and was clicking even trying to print abs

]]> Mon, 31 Aug 2015 14:56:24 +0000 https://www.soliforum.com/post/104557/#p104557 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104550/#p104550 kev0175 wrote:

I just wanted to make sure but in your fan on the E3D hooked up to a 12v supply?

Its hooked up to the 3D printers power supply to the 12 V rail. Test print looks good 5 hours now almost done. Some cracks but overall good.

]]> Mon, 31 Aug 2015 14:14:00 +0000 https://www.soliforum.com/post/104550/#p104550 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104544/#p104544 I just wanted to make sure but in your fan on the E3D hooked up to a 12v supply?

]]> Mon, 31 Aug 2015 10:04:29 +0000 https://www.soliforum.com/post/104544/#p104544 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104541/#p104541 evanalmighty wrote:

My da Vinci e3d Bowden setup retraction is set at 3mm, retraction speed is 50, and XY movement speed is 120mm/s

Ok tryed it dont work for me at all I am currently running a test with 3mm retraction 40mm/s and canola oil. Do you print PLA ?

]]> Mon, 31 Aug 2015 08:42:58 +0000 https://www.soliforum.com/post/104541/#p104541 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104316/#p104316 evanalmighty wrote:

My da Vinci e3d Bowden setup retraction is set at 3mm, retraction speed is 50, and XY movement speed is 120mm/s

I tryed its creating strings i set it to 3.5mm I will test it tomorrow. Thanks

]]> Thu, 27 Aug 2015 18:56:37 +0000 https://www.soliforum.com/post/104316/#p104316 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104256/#p104256 My da Vinci e3d Bowden setup retraction is set at 3mm, retraction speed is 50, and XY movement speed is 120mm/s

]]> Wed, 26 Aug 2015 15:18:11 +0000 https://www.soliforum.com/post/104256/#p104256 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/104241/#p104241 elmoret wrote:

4.5 is also a lot of retract. Have you read E3D's documentation, including the page on extrusion issues?

I did what retract do you recommend to start trying with?

]]> Wed, 26 Aug 2015 12:41:18 +0000 https://www.soliforum.com/post/104241/#p104241 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/103988/#p103988 4.5 is also a lot of retract. Have you read E3D's documentation, including the page on extrusion issues?

]]> Fri, 21 Aug 2015 22:07:20 +0000 https://www.soliforum.com/post/103988/#p103988 <![CDATA[Re: Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/103979/#p103979 190 is the normal minimum for most PLA. Some will need as much as 210.

]]> Fri, 21 Aug 2015 19:17:31 +0000 https://www.soliforum.com/post/103979/#p103979 <![CDATA[Da Vinci 1.0A, Repetier Host, E3D v6 Bowden Retraction]]> https://www.soliforum.com/post/103977/#p103977 Hello since I upgraded my printer to a bowden setup it starts clicking again.Before I upgraded 175°C PLA worked fine now its jamming.
Settings:
avoid_crossing_perimeters = 0
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 0
before_layer_gcode =
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 0
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.2
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF8000
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 10%
first_layer_temperature = 170
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 40
interface_shells = 0
layer_gcode =
layer_height = 0.3
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 10
notes =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 2
post_process =
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4.5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 70%
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 75%
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 1
support_material_interface_spacing = 0
support_material_interface_speed = 75%
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 20
support_material_threshold = 10
temperature = 175
thin_walls = 1
threads = 8
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0

]]> Fri, 21 Aug 2015 18:38:48 +0000 https://www.soliforum.com/post/103977/#p103977