<![CDATA[SoliForum - 3D Printing Community — Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/topic/11867/solidoodle-2-firmware-for-sanguinololu-13/ Tue, 04 Aug 2015 23:50:56 +0000 PunBB <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102904/#p102904 As long as it works I wouldn't worry about it too much.

]]> Tue, 04 Aug 2015 23:50:56 +0000 https://www.soliforum.com/post/102904/#p102904 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102902/#p102902 Strange.  Seems to be working now but only when I have the jumper removed.

I'll keep playing with it, thanks!

]]> Tue, 04 Aug 2015 23:38:12 +0000 https://www.soliforum.com/post/102902/#p102902 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102431/#p102431 It is supposed to have a jumper on it if that's the one you're talking about.

]]> Thu, 30 Jul 2015 13:45:51 +0000 https://www.soliforum.com/post/102431/#p102431 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102422/#p102422 The jumper between the Micro and the Z extruder StepStick is closed/shorted on mine. And I have never touched it. I have used the Arduino IDE several times to update the firmware.

]]> Thu, 30 Jul 2015 06:49:33 +0000 https://www.soliforum.com/post/102422/#p102422 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102387/#p102387 I haven't used a Sang for a while  but I have a photo to look at and I am unsure what jumper you are speaking of.  Can you post a clear picture of your whole board and point out the jumper?

]]> Wed, 29 Jul 2015 22:58:27 +0000 https://www.soliforum.com/post/102387/#p102387 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102382/#p102382 bump?  anyone know what the jumper should be set to?

]]> Wed, 29 Jul 2015 22:25:46 +0000 https://www.soliforum.com/post/102382/#p102382 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102057/#p102057 wardjr wrote:

Just use this one and make any changes you need.  https://github.com/ozadr1an/Solidoodle- … in_v1_beta
The one you are trying to use has some things enabled that you don't have on your printer.

I have just tried building/uploading that firmware (with version set for v2 instead of v3 printer, and uncomment bed PID).
I'm still seeing it hang at "Command waiting" intermittently when I first try to connect.

I see mention of an "autoreset" jumper in reprap Sanguinololu documentation, my printer has this jumper set in the "shorted" position from the factory.  I just tried disassembling the cover and moved the jumper to the "open" position and the "Command waiting" seems to have gone away.  I see notes about "reset during print" with the jumper closed.

What position should this "autoreset" jumper be set to for normal operation of my Solidoodle2?  Was it possibly incorrectly configured by mistake from the factory and I was just lucky it worked until I messed with it?

]]> Sun, 26 Jul 2015 18:26:22 +0000 https://www.soliforum.com/post/102057/#p102057 <![CDATA[Re: Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102044/#p102044 Just use this one and make any changes you need.  https://github.com/ozadr1an/Solidoodle- … in_v1_beta
The one you are trying to use has some things enabled that you don't have on your printer.

]]> Sun, 26 Jul 2015 13:56:42 +0000 https://www.soliforum.com/post/102044/#p102044 <![CDATA[Solidoodle 2 Firmware for Sanguinololu 1.3]]> https://www.soliforum.com/post/102037/#p102037 I need to locate working firmware to reload on my Solidoodle 2 Sanguinololu 1.3 controller board.

I was attempting to enable heat-bed PID control and tried to flash a firmware from https://github.com/mlaws/solidoodle2-marlin but now I'm stuck where either I can't control speed on-the-fly (no M115 report with the beta?) or I can't get the printer to connect properly stuck at "Waiting for command" (with the non-beta).

Is there anywhere I can get either a .hex (preferred) or code to compile for what my Solidoodle 2 would have shipped with that works well?

I have an ISP programmer.

]]> Sun, 26 Jul 2015 03:44:41 +0000 https://www.soliforum.com/post/102037/#p102037