<![CDATA[SoliForum - 3D Printing Community — SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/topic/11719/sd3-repetier-stops-print-due-to-temperature-215c/ 215C.]]> Thu, 16 Jul 2015 18:43:39 +0000 PunBB <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101348/#p101348 just saw the screen shot, ignore last post.....working on it

Joe

]]> Thu, 16 Jul 2015 18:43:39 +0000 https://www.soliforum.com/post/101348/#p101348 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101347/#p101347 thanks, tried that, but I nus have done it wrong

]]> Thu, 16 Jul 2015 18:43:02 +0000 https://www.soliforum.com/post/101347/#p101347 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101318/#p101318 http://soliforum.com/i/?x1mv6MG.png

]]> Thu, 16 Jul 2015 16:58:40 +0000 https://www.soliforum.com/post/101318/#p101318 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101314/#p101314 Looking at the hardware folder within MARLIN you will need to pull the right folder and move it there.
I'll get you a screen shot.

]]> Thu, 16 Jul 2015 16:45:32 +0000 https://www.soliforum.com/post/101314/#p101314 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101311/#p101311 I've got the configuration.h changed

I'm having trouble with finding the board and getting the Marlin board type into the Arduino 0022

]]> Thu, 16 Jul 2015 16:31:40 +0000 https://www.soliforum.com/post/101311/#p101311 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101269/#p101269 That's a Sang and is very easy to flash.
1. Download Arduino .022
2. Download this firmware https://github.com/ozadr1an/Solidoodle- … in_v1_beta
3. Open the marlin.ino file from the folder you just downloaded.
4. Click on the configuration.h tab and make (or verify) these changes.

// change to 3 for SD3 //{SD Patch}
#define SOLIDOODLE_VERSION 3 //{SD Patch}

#ifndef MOTHERBOARD
#define MOTHERBOARD 62

#define TEMP_SENSOR_0 5    //{E3D}

#define HEATER_0_MAXTEMP 300

5. Click the Save Button
6. Under the "Tools" tab in the "Board" section choose your board (Sanguinololu or Sanguino)  If it isn't there you will need to find the hardware folder from the Marlin folders that SD posts on their website and move it into the appropriate folder of this new versions folder.
7. Choose the correct com port in the same tools tab.
8. Hit reset on the board and click upload.
When it is done it will say done uploading and that is it.
There are really good instructions on the process in the WIKI so look through them as I may have missed something.
http://www.soliwiki.com/Updating_Solidoodle_Firmware

]]> Wed, 15 Jul 2015 23:21:17 +0000 https://www.soliforum.com/post/101269/#p101269 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/101239/#p101239 Thanks Heartless,
Thanks Wardjr

Just got the new tip delivered....want to work on that tonight

per your request, pictures of my boardhttp://soliforum.com/i/?g8K4Tua.jpg

]]> Wed, 15 Jul 2015 20:04:22 +0000 https://www.soliforum.com/post/101239/#p101239 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100984/#p100984 wardjr is da man when it comes to firmware, he wont steer you wrong. big_smile

]]> Mon, 13 Jul 2015 02:34:55 +0000 https://www.soliforum.com/post/100984/#p100984 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100951/#p100951 Tell me what board you have or take a picture and I'll link you the proper set of instructions..

]]> Sun, 12 Jul 2015 17:51:48 +0000 https://www.soliforum.com/post/100951/#p100951 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100944/#p100944 good to know, thanks heartless and ward

I was going to attempt to clean out the original nozzle, but from what I'm hearing I guess I should abandon that assembly.

I'll follow the directions carefully, in the meantime I can start working on the firmware upgrade.


Not sure where to start there...I would also want to make sure that I can run hotter than 215C without that annoying auto shut down thing

Joe

]]> Sun, 12 Jul 2015 16:37:01 +0000 https://www.soliforum.com/post/100944/#p100944 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100921/#p100921 Heartless knows what she's talking about so I second her post.
Don't mess with kapton and just get a piece of glass cut at the local hardware store.  Then buy a can of Aquanet extreme hold hairspray.  Spray the bed (kapton in place or not) then stick the glass on the bed.  Spray a nice mist coat on the top of the glass and let dry.   Maybe repeat this to ensure a nice even application.  Then adjust your Z end stop to compensate for the new bed height.  I try to avoid binder clips to hold the glass, if the bed is warped the glass will be too.  With hairspray it will fill in the gaps. 
The. Heat cool cycle 3 times and the glass will stick yet be removable.

]]> Sun, 12 Jul 2015 03:31:14 +0000 https://www.soliforum.com/post/100921/#p100921 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100919/#p100919 you wont need either the kapton tape or the black insulation for the E3d swap, they are completely unnecessary. You will receive everything you need for the E3d in the kit (except for the actual mount to mount it on your printer)

You do want to follow the assembly instructions - to the letter.

You will need to update the firmware in order to get the proper temperatures with the new hotend, especially for the crucial final tightening of the nozzle.

I have an E3D v6 on my SD4 and love it.

I have a degree in mechanical engineering, so that just makes me dangerous.

ha-ha, I don't have a degree, but I know just enough to make me dangerous! wink

"Jack (Jill) of all trades, master of none...
Know a little bit about a lot of things,
and a whole lot about nothing"

The quest for knowledge never ends...

]]> Sun, 12 Jul 2015 02:12:33 +0000 https://www.soliforum.com/post/100919/#p100919 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100907/#p100907 Ward, I'm a bit frustrated by the nozzle failure.  I'm already developing a customer need for parts and I'm out of business right now.

my plan is to have multiple extrusion assemblies so that I can do better on delivery.  I'll likely get another machine at some point.

I'm a middle school science teacher and I think that ir would be cool to do a winter camp where a group of kids put together and modify a kit type printer.  I'll include the cost of the printer in the camp cost.....what parent could resist that?  At the end, the kid takes the printer home!!!

Anyways, I digress 

When I manually exrude the filament, it does everything but come out smoothly. 

doing my research and seeing what is on the extrusion assembly...I will need some supplies.  I want to review this with you.

Kapton tape (can you confirm the exact type or part number.  what width would you get?)
I see there is a sort of black/asbestos looking tape around the heater block.  I assume that is for insulation.  what is that?

what else should I have on hand for this exchange?

I have a degree in mechanical engineering, so that just makes me dangerous.

thanks, Joe

]]> Sat, 11 Jul 2015 21:43:33 +0000 https://www.soliforum.com/post/100907/#p100907 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100851/#p100851 good to know, still using original acrylic

]]> Sat, 11 Jul 2015 00:06:54 +0000 https://www.soliforum.com/post/100851/#p100851 <![CDATA[Re: SD3 Repetier stops print due to temperature ~>215C]]> https://www.soliforum.com/post/100848/#p100848 Yep but you need a mount if your still using the original acrylic.  If you contact Filastruder you can buy one for like $5.  It is just a temp to get you up and running.

]]> Fri, 10 Jul 2015 23:53:59 +0000 https://www.soliforum.com/post/100848/#p100848