<![CDATA[SoliForum - 3D Printing Community — Printer not heating up]]> https://www.soliforum.com/topic/11658/printer-not-heating-up/ Mon, 06 Jul 2015 20:09:10 +0000 PunBB <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100533/#p100533 http://e3d-online.com/Spares/Thermistor-Replacement-Kit

This is the actual sensor from an E3D this work before I just ordered a new one to see if that will work

]]> Mon, 06 Jul 2015 20:09:10 +0000 https://www.soliforum.com/post/100533/#p100533 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100498/#p100498 you cannot use any thermistor on Davinci because it has additionnal resistor, so table need to be modified, it cannot be use as it is

http://voltivo.com/forum/davinci-firmwa … ruder#3631

]]> Mon, 06 Jul 2015 06:00:48 +0000 https://www.soliforum.com/post/100498/#p100498 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100497/#p100497 And no this is running repertier 0.91

]]> Mon, 06 Jul 2015 05:21:58 +0000 https://www.soliforum.com/post/100497/#p100497 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100496/#p100496 Yeah it's cold but reads 359 then errors out. It's a new sensor. If it happens with the E3D official one then I'm parting the machine out getting another different one

]]> Mon, 06 Jul 2015 05:21:38 +0000 https://www.soliforum.com/post/100496/#p100496 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100492/#p100492 sensor defect, so you are in dry mode to avoid problem
if you said you read 359 when starting, because sensor has a limit of 300, over this temperature it consider the measurement has a problem, so it go to dry mode to prevent heating.
You also can connect repetier to see what temperature is measured, def is only on LCD
Looks like sensor problem, if at room temperature it give 359 degres, it is not normal

]]> Sun, 05 Jul 2015 23:46:34 +0000 https://www.soliforum.com/post/100492/#p100492 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100488/#p100488 Is this a stock machine or modified? I don't remember what the stock LCD looks like.

]]> Sun, 05 Jul 2015 21:41:55 +0000 https://www.soliforum.com/post/100488/#p100488 <![CDATA[Re: Printer not heating up]]> https://www.soliforum.com/post/100482/#p100482 I have since changed out the thermister twice and this time when i connect it it reads 359 and then reads def

Really don't know what to do and am getting desperate for help here

]]> Sun, 05 Jul 2015 18:51:33 +0000 https://www.soliforum.com/post/100482/#p100482 <![CDATA[Printer not heating up]]> https://www.soliforum.com/post/100325/#p100325 I've come to heat my printer up to put filament in and it just says DEF next to the temps and is not warming up. Attached a picture to help people understand

Hope some one can help
http://soliforum.com/i/?CBTzxJs.jpg

]]> Thu, 02 Jul 2015 14:00:30 +0000 https://www.soliforum.com/post/100325/#p100325