<![CDATA[SoliForum - 3D Printing Community — Windows 10]]> https://www.soliforum.com/topic/11503/windows-10/ Fri, 27 May 2016 03:25:26 +0000 PunBB <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/123481/#p123481 fred.steffen wrote:

I just upgraded my Win7 machine to Win10, DaVinci 1.0, using the XYZWare Open mod software. With the Open Mod or the stock XYZWare, I'm getting "device not found". I haven't been able to figure out how to get it to work either. If anyone has any ideas, I'd love to hear em'. If I can't get it running, I'll pull out an old Win7 laptop and use that lol...

I'm using 3rd party spool, as I don't want to pay 2x - 4x for filament, so no upgrading the software for me. This might be enough to push me into uploading the Repitier firmware and bypassing XYZWare all together.

I know this is months later but it may save someone like me trouble shooting and finding nothing.

So I had my Da Vinci packed away since september because of moving and not having enough time to print. I came across this problem on my new system. I looked at my tablet I have that has window 10 non 1511 update. I noticed the driver is different on the tablet then what is on my new desktop.

  • Uninstall the device from device manager and tell it to remove drivers.

  • Plug it back. You will briefly see "XYZ Printing, 3D Printer Da Vinci (COM 3)" before updating to the new windows built in driver.

  • After it switches to the new driver Right click, select properties, Click the Driver Tab and select Roll Back Driver.

  • Your Open Mod Software will now see the printer.

Be warned you will have to do it again if you open 3D Builder because it appears to update the driver when you do. Which might be the reason my tablet could also see it because i never opened the 3d Builder software on it.

]]> Fri, 27 May 2016 03:25:26 +0000 https://www.soliforum.com/post/123481/#p123481 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/103168/#p103168 I was having a similar problem on Repetier with my Davinci 1.0A after upgrading to windows 10. A print would start off normally, but once everything was in position the extruder would not heat up and I would get a "communication timeout - reset send buffer block" message before my printer went idle. I fixed this by going to printer settings and changing Reset on Connect to Due native USB port.

]]> Fri, 07 Aug 2015 18:32:34 +0000 https://www.soliforum.com/post/103168/#p103168 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/103029/#p103029 Ok as an FYI I installed the latest xyz software to try it in windows 10 since I decided to flash my 1.0A anyway and it works as it did before, and yes the resetter still works fine as well. I will most likely still flash it anyway but anybody who was wondering there is your answer.

]]> Thu, 06 Aug 2015 03:28:48 +0000 https://www.soliforum.com/post/103029/#p103029 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/103016/#p103016 Rhino4824 wrote:

Thanks for the input!

I would do both. I switched to Repetier in fact I even replaced my logic for  RAMPS 1.4 and it made a world of difference. But there where still some prints giving me a fuss. I got S3D and all the prints came out perfect with minimal setting changes from what S3D installs with.

]]> Thu, 06 Aug 2015 01:39:37 +0000 https://www.soliforum.com/post/103016/#p103016 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/103014/#p103014 Thanks for the input!

]]> Thu, 06 Aug 2015 01:20:20 +0000 https://www.soliforum.com/post/103014/#p103014 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102995/#p102995 Rhino4824 wrote:

Ok guys assuming the cost of simplify wasn't an issue would you flash or use simplify?

Both - I flashed my 1.0 with Repetier and use Simplify. (But I run mine off a Mac, so the Win10 aspect doesn't affect this printer).

]]> Wed, 05 Aug 2015 19:10:45 +0000 https://www.soliforum.com/post/102995/#p102995 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102965/#p102965 Ok guys assuming the cost of simplify wasn't an issue would you flash or use simplify?

]]> Wed, 05 Aug 2015 15:38:03 +0000 https://www.soliforum.com/post/102965/#p102965 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102964/#p102964 Unfortunately I wont be bothering with W10 on my printer PC. I have a dedicated PC for my printer thats running just fine on 7 + Repetier

]]> Wed, 05 Aug 2015 15:24:25 +0000 https://www.soliforum.com/post/102964/#p102964 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102963/#p102963 rforeman wrote:

What about Simplify 3D and Windows 10. Will it connect to the DaVinci ?

Yes, this works with Win10 64 bit on my desktop.

]]> Wed, 05 Aug 2015 15:14:33 +0000 https://www.soliforum.com/post/102963/#p102963 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102950/#p102950 I also got the wrong cartridge error about 10 seconds after it started to print, guess I will flash it this chasing things around to get something to work is getting old.

]]> Wed, 05 Aug 2015 10:26:00 +0000 https://www.soliforum.com/post/102950/#p102950 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102948/#p102948 I see the printer in windows 10
i also see it writes a offline_printing file on my sd card but then it reports wrong filament placed.
I cannot change the filament and because i only have PLA i cannot change it.

Johan

]]> Wed, 05 Aug 2015 09:36:43 +0000 https://www.soliforum.com/post/102948/#p102948 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102946/#p102946 I see MS have taken out the scan option in windows 10. I will stay on win 8.1 for now. But things are looking up  smile

]]> Wed, 05 Aug 2015 06:49:19 +0000 https://www.soliforum.com/post/102946/#p102946 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102940/#p102940 What about Simplify 3D and Windows 10. Will it connect to the DaVinci ?

]]> Wed, 05 Aug 2015 04:22:29 +0000 https://www.soliforum.com/post/102940/#p102940 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102814/#p102814 So I sent a file from the 3d builder app in win10 to my 1.0a, screen said receiving job and it began to print and I mean it went right to printing with no extruder or bed warmup and obviously no filament extruded since it was cold.  I ran out of time to look into it any further but maybe later on I can get back to it.

]]> Mon, 03 Aug 2015 23:21:15 +0000 https://www.soliforum.com/post/102814/#p102814 <![CDATA[Re: Windows 10]]> https://www.soliforum.com/post/102811/#p102811 I'm not sure on this to be honest. I think the firmware might be able to stay where it is. It's the drivers that are going to be updated which allow communication with the printer. Also because you are using a different application it might be better for XYZ owners as it might allow more function.

Need to do some testing first but I've downloaded the 3d model on my Windows 8.1 machine but it wont write to my printer.. I was holding off Win10 install but this might just make it worth while...

Who's going to try first?    lol

]]> Mon, 03 Aug 2015 22:12:02 +0000 https://www.soliforum.com/post/102811/#p102811