<![CDATA[SoliForum - 3D Printing Community — Motor noise and startup noise]]> https://www.soliforum.com/topic/11019/motor-noise-and-startup-noise/ Thu, 07 May 2015 21:36:14 +0000 PunBB <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/95147/#p95147 Just FYI, my fan does quiet down after 30 seconds, so I haven't been motivated to dig too deeply, but it would be nice to fix.

Ghostling wrote:

i have the same fan noise on startup on my sd2pro on the extruder stepper cooler. it usually quiets down after about 30 seconds. i think i'm just going to replace the crap quality fan with a better one.

Let us know how that goes!

Illy wrote:

Hey, that's my video!

You caught me!

]]> Thu, 07 May 2015 21:36:14 +0000 https://www.soliforum.com/post/95147/#p95147 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/95080/#p95080 i have the same fan noise on startup on my sd2pro on the extruder stepper cooler. it usually quiets down after about 30 seconds. i think i'm just going to replace the crap quality fan with a better one.

]]> Thu, 07 May 2015 03:42:45 +0000 https://www.soliforum.com/post/95080/#p95080 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/95070/#p95070 Tighten your fan nuts, and then check em regularly. I've literally just now sorted out some fan noise problem with this very step. Rattly little sod shook its self right off my stepper.

]]> Thu, 07 May 2015 00:41:48 +0000 https://www.soliforum.com/post/95070/#p95070 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/95069/#p95069 Hey, that's my video!

I'm still actually having the same problem. After digging around the insides a bit I found out that it was actually the fan near the motherboard making that noise, and not the back fan. So far I've been kind of jerry-rigging it into a quiet state by sticking my hand in and tapping the center of the fan while it's running. Eventually it realigns the bits and pieces and makes it run quiet for the rest of the night. I've found for some reason turning the printer on and off a few times during this process helps get it to behave quicker too.

I have plans this weekend to pop the bottom panel open and actually oil the fan. I'll let you know how it goes!

]]> Thu, 07 May 2015 00:31:39 +0000 https://www.soliforum.com/post/95069/#p95069 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/95016/#p95016 @trayracing: I already print with the mainboard outside and with a fan over E stepper driver wink So that fan is useless for me if it does what you say it does. The E stepper driver overheating is a problem that I have looooooooong time before I removed the chamber fan.

]]> Wed, 06 May 2015 10:21:37 +0000 https://www.soliforum.com/post/95016/#p95016 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94997/#p94997 madfalcon81 wrote:

I removed the back fan. Dont know if I did good.

It ejects air from the back, and if everything is shut up, pulls air in through slits in the bottom.  (Speculation alert...) Removing the back fan might be depriving the controller board of cool air and be related to your E stepper chip overheating. BTW, if your stepper chip is overheating, consider adding a stick-on heat sink to the chip. Search for "Aluminum Self-adhensive Heatsink For 3D printer A4988" or something like that on ebay.

pshcims: first step is to make sure wires aren't dangling against the back fan or bottom fan. I used to have a loud fan, but it's since down to a dull roar, so there's hope.

]]> Tue, 05 May 2015 23:18:02 +0000 https://www.soliforum.com/post/94997/#p94997 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94985/#p94985 jagowilson wrote:

Those fans SD uses are cheap. I had the same issue on my 4. As for the motors you can turn down VREF a bit but steppers are kinda loud anyway.

What is VREF?

What did you do about your fan?

]]> Tue, 05 May 2015 21:08:37 +0000 https://www.soliforum.com/post/94985/#p94985 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94945/#p94945 I removed the back fan. Dont know if I did good.

]]> Tue, 05 May 2015 14:25:33 +0000 https://www.soliforum.com/post/94945/#p94945 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94929/#p94929 Those fans SD uses are cheap. I had the same issue on my 4. As for the motors you can turn down VREF a bit but steppers are kinda loud anyway.

]]> Tue, 05 May 2015 04:00:39 +0000 https://www.soliforum.com/post/94929/#p94929 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94926/#p94926 jagowilson wrote:

That's not a motor it's a fan. It sounds like it's just unbalanced. Find the problematic fan and either replace it or take it apart and line it up. Might need some oil too.

I am having 2 issues, the motors AND the fan. I edited my original post to clarify.

The fan is the one of the rear of the printer. I'm looking to see if anyone else has had the same issue (besides the YouTube poster).

]]> Tue, 05 May 2015 03:33:33 +0000 https://www.soliforum.com/post/94926/#p94926 <![CDATA[Re: Motor noise and startup noise]]> https://www.soliforum.com/post/94923/#p94923 That's not a motor it's a fan. It sounds like it's just unbalanced. Find the problematic fan and either replace it or take it apart and line it up. Might need some oil too.

]]> Tue, 05 May 2015 03:20:42 +0000 https://www.soliforum.com/post/94923/#p94923 <![CDATA[Motor noise and startup noise]]> https://www.soliforum.com/post/94916/#p94916 I am having 2 issues:

First, the stepper motor noise is a major nuisance, has anyone found a way to reduce it?

Second, my unit now makes a large noise when starting up similar to this video below. Another post indicates that a fan is failing. Has anyone replaced this or asked Solidoodle for support?

]]> Tue, 05 May 2015 02:20:05 +0000 https://www.soliforum.com/post/94916/#p94916