<![CDATA[SoliForum - 3D Printing Community — Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/topic/10981/tried-updating-firmware-it-isnt-uploading/ Sat, 02 May 2015 01:52:45 +0000 PunBB <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94676/#p94676 Are you sure you have the correct com port selected in RH.
you'll also want to make sure "auto reset on connect" is disabled in RH.

]]> Sat, 02 May 2015 01:52:45 +0000 https://www.soliforum.com/post/94676/#p94676 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94667/#p94667 Now I was able to flash it and boot, printer still doesn't respond.

]]> Sat, 02 May 2015 00:05:24 +0000 https://www.soliforum.com/post/94667/#p94667 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94664/#p94664 wardjr wrote:

No other way and I know it looks daunting but really isn't that bad.  I have done it many times as have many other users.  Should only take a first timer an hour and after that it's about a 10 minute thing.  Good luck smile

Computer doesn't seem to be recognizing the board after booting.

]]> Fri, 01 May 2015 23:26:27 +0000 https://www.soliforum.com/post/94664/#p94664 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94663/#p94663 No other way and I know it looks daunting but really isn't that bad.  I have done it many times as have many other users.  Should only take a first timer an hour and after that it's about a 10 minute thing.  Good luck smile

]]> Fri, 01 May 2015 23:08:14 +0000 https://www.soliforum.com/post/94663/#p94663 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94661/#p94661 wardjr wrote:

That's a printerboard follow the printerboard instructions on the WIKI.

Any other way? When I'm at the last steps I get a message from the command prompt that the BootloaderHId is not recognized as an internal or external command.

hmm

]]> Fri, 01 May 2015 22:45:29 +0000 https://www.soliforum.com/post/94661/#p94661 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94660/#p94660 That's a printerboard follow the printerboard instructions on the WIKI.

]]> Fri, 01 May 2015 22:14:17 +0000 https://www.soliforum.com/post/94660/#p94660 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94658/#p94658 http://soliforum.com/i/?XRgUodr.jpg

Here it is, thank you.

]]> Fri, 01 May 2015 21:58:39 +0000 https://www.soliforum.com/post/94658/#p94658 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94657/#p94657 Take a picture and post it I'll tell you.

]]> Fri, 01 May 2015 21:52:35 +0000 https://www.soliforum.com/post/94657/#p94657 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94656/#p94656 wardjr wrote:

Make sure you have the correct board chosen in configuration.h.
Also in Arduino under tools you need to select the correct board.  If it isn't in the drop down under "board" then you need to locate that hardware folder and move it to the correct location.

How can I make double check my board? I'm using the one according with the instructions. "Sanguino W/ ATmega644P"

]]> Fri, 01 May 2015 21:46:38 +0000 https://www.soliforum.com/post/94656/#p94656 <![CDATA[Re: Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94655/#p94655 Make sure you have the correct board chosen in configuration.h.
Also in Arduino under tools you need to select the correct board.  If it isn't in the drop down under "board" then you need to locate that hardware folder and move it to the correct location.

]]> Fri, 01 May 2015 21:29:05 +0000 https://www.soliforum.com/post/94655/#p94655 <![CDATA[Tried updating firmware, it isn't uploading]]> https://www.soliforum.com/post/94654/#p94654 Hello everyone,

I tried to flash the firmware with the hysteresis fix, downloaded it here and followed instructions.
https://github.com/ozadr1an/Solidoodle- … in_v1_beta

I'm getting this error "avrdude: stk500_getsync(): not in sync: resp=0x00" after trying to upload it in Arduino 1.0.5, now the 3d printer connects to the slicer but doesn't react to any instructions. I've a Solidoodle 3.

]]> Fri, 01 May 2015 21:22:01 +0000 https://www.soliforum.com/post/94654/#p94654