<![CDATA[SoliForum - 3D Printing Community — K resistor value at 3.3v positive]]> https://www.soliforum.com/topic/10963/k-resistor-value-at-33v-positive/ Sat, 02 May 2015 14:24:37 +0000 PunBB <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94707/#p94707 I found these on mouser, I'm not sure if they are the right fuses one is a 1206 and the other is a 0603 series 437 and 438

mouser.com/Search/m_ProductDetail.aspx? … bcXMv8V6g=

mouser.com/Search/m_ProductDetail.aspx? … omAxZUVpw=

]]> Sat, 02 May 2015 14:24:37 +0000 https://www.soliforum.com/post/94707/#p94707 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94542/#p94542 Its not the best soldering job but that resistor is zero ohms.


http://soliforum.com/i/?OEwpYAP.jpg

]]> Thu, 30 Apr 2015 18:51:18 +0000 https://www.soliforum.com/post/94542/#p94542 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94541/#p94541 Hmm. a while back I soldered a zero ohm resistor there and it made one of the diodes turn off furthering more problems to my board.

]]> Thu, 30 Apr 2015 18:48:50 +0000 https://www.soliforum.com/post/94541/#p94541 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94537/#p94537 barry1685 wrote:

Bottom Resistor labeled "K" is R57 and top one is R47

You have one of the newer boards. Those are just zero ohm resistors that are being used as fuses to my knowledge. Based off of other post where they have been burned. The second rev boards like mine do not have them

]]> Thu, 30 Apr 2015 18:28:06 +0000 https://www.soliforum.com/post/94537/#p94537 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94519/#p94519 Bottom Resistor labeled "K" is R57 and top one is R47

]]> Thu, 30 Apr 2015 17:29:15 +0000 https://www.soliforum.com/post/94519/#p94519 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94518/#p94518 Sure. See below.http://soliforum.com/i/?MMQ3oaX.jpg

]]> Thu, 30 Apr 2015 17:28:12 +0000 https://www.soliforum.com/post/94518/#p94518 <![CDATA[Re: K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94515/#p94515 barry1685 wrote:

Does anyone know what the "k" resistor is on the circuit board. It is right at the 3.3v power input.


Could you post a picture. I have a stock board just collecting dust now but I see no resistor near the 3.3v input.

]]> Thu, 30 Apr 2015 16:30:11 +0000 https://www.soliforum.com/post/94515/#p94515 <![CDATA[K resistor value at 3.3v positive]]> https://www.soliforum.com/post/94502/#p94502 Does anyone know what the "k" resistor is on the circuit board. It is right at the 3.3v power input.

]]> Thu, 30 Apr 2015 15:04:22 +0000 https://www.soliforum.com/post/94502/#p94502