<![CDATA[SoliForum - 3D Printing Community — Extruder not unloading because not heating up]]> https://www.soliforum.com/topic/10494/extruder-not-unloading-because-not-heating-up/ Thu, 11 Oct 2018 16:24:15 +0000 PunBB <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/146862/#p146862 kev0175 wrote:

Have you tried the auto heat in your settings I think it will heat the extruder up to 185c but it seems to me that it may be a defect. What firmware do you have on the printer right now?

Super - You saved my day :-) I´ve bought one Davinci Duo on ebay without cartrigdes - and he reports me error 0012, as I´ve tried to unload the filament, without heating up. The "AUTO HEAT" Function goes very well instaed = no hardware issue :-)

Thanks a lot + God bless you!

]]> Thu, 11 Oct 2018 16:24:15 +0000 https://www.soliforum.com/post/146862/#p146862 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/119368/#p119368 just had this same problem where it wouldn't heat up during unload and the cartridge shows as not present when you do a "load cartridge" - had to take the cartridge out (leaving the filament in), then clean the contacts on the cartridge and reseat it, after that it recognised.

]]> Wed, 16 Mar 2016 07:08:03 +0000 https://www.soliforum.com/post/119368/#p119368 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90935/#p90935 Also did you block the xyz.exe

]]> Thu, 26 Mar 2015 13:53:03 +0000 https://www.soliforum.com/post/90935/#p90935 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90934/#p90934 I'm thinking its the cartridges, if you can reset the cartridge it should work and if it doesn't I'm thinking firmware glitch.

]]> Thu, 26 Mar 2015 13:52:19 +0000 https://www.soliforum.com/post/90934/#p90934 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90777/#p90777 Load didn't work for me either

]]> Wed, 25 Mar 2015 14:47:11 +0000 https://www.soliforum.com/post/90777/#p90777 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90775/#p90775 Had the same problem yesterday or the first time - here's what I did:
Although the Unload didn't heat the extruder, the Load Cartridge did so, I cut the old filament and selected Load Cartridge.
I chased the remaining old filament with new filament (meaning, I just followed the old with the new).
Then, I pressed the <- arrow to Load again at the prompt asking if the filament came out of the nozzle and repeated once more until the new filament feed.
It worked.

]]> Wed, 25 Mar 2015 14:45:51 +0000 https://www.soliforum.com/post/90775/#p90775 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90746/#p90746 I have mine on autoheat,, then it works and unloads... it is a firmware glitch and I think there's a fix, but I don't trust any downloads from XYZ so I just deal with it.. Also, I should add that mine isn't a 1aio,,, only a 1.a.

]]> Wed, 25 Mar 2015 02:03:40 +0000 https://www.soliforum.com/post/90746/#p90746 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90417/#p90417 I don't know if a resetter will help the cartridges

]]> Sat, 21 Mar 2015 22:55:37 +0000 https://www.soliforum.com/post/90417/#p90417 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90412/#p90412 You can try this, it may not work but sometimes when my printer acts a little weird I will turn it off hold the up and down button turn it on and that with bring up the boot loader  I will wait a while then turn it off then back on again but like I said it may not help.

]]> Sat, 21 Mar 2015 20:27:53 +0000 https://www.soliforum.com/post/90412/#p90412 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90388/#p90388 The system version 1.1.4 but I don't think it's a firmware issue

]]> Sat, 21 Mar 2015 16:16:06 +0000 https://www.soliforum.com/post/90388/#p90388 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90387/#p90387 @evanalmight it doesn't load as it says all my cartridges aren't loaded, it's probably because of that problem with the extruder. Not sure.

@kev0175, I'll check the firmware asap

]]> Sat, 21 Mar 2015 16:08:13 +0000 https://www.soliforum.com/post/90387/#p90387 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90380/#p90380 Have you tried the auto heat in your settings I think it will heat the extruder up to 185c but it seems to me that it may be a defect. What firmware do you have on the printer right now?

]]> Sat, 21 Mar 2015 15:36:33 +0000 https://www.soliforum.com/post/90380/#p90380 <![CDATA[Re: Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90378/#p90378 Instead of using the unload feature, do the loading instead.  As soon as it's done extruding material, pull back on the spring loaded lever and pull the filament out by hand.

]]> Sat, 21 Mar 2015 15:29:42 +0000 https://www.soliforum.com/post/90378/#p90378 <![CDATA[Extruder not unloading because not heating up]]> https://www.soliforum.com/post/90374/#p90374 Hey guys,

Ok so here is my problem.

My DaVinci Printer AIO doesn't heat up when I try to unload filament but it does heat up when I do a nozzle cleaning so the heating functions still well.

If it's heated up and I quickly change to unload filament in the hopes of it still being hot enough, it cools down until it's completely cold.

I can't load any filament as it says that all my cartridges are not loaded. This issue is working on my nerves and I'm hoping there is some bright mind on this forum that has an easy solution for this.

Well thanks in advance.

Ignace

]]> Sat, 21 Mar 2015 15:06:27 +0000 https://www.soliforum.com/post/90374/#p90374