<![CDATA[SoliForum - 3D Printing Community — (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/topic/10234/stock-xyzware-issue-device-not-found/ Mon, 02 Mar 2015 22:57:28 +0000 PunBB <![CDATA[Re: (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87959/#p87959 Well I know I had a few issues with mine made the switch and I can finally fine tune it and fail it in. All you need to buy is a SD card extension so you can route the card holder into the print area for easy access

]]> Mon, 02 Mar 2015 22:57:28 +0000 https://www.soliforum.com/post/87959/#p87959 <![CDATA[Re: (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87950/#p87950 Would you recommend trying to do something like this though without it correctly working on stock right now?

]]> Mon, 02 Mar 2015 22:36:19 +0000 https://www.soliforum.com/post/87950/#p87950 <![CDATA[Re: (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87948/#p87948 Well you can set temperatures so there is more control doing it that way I run my filament at 240 Degrees C and bed at 85 Degrees C and works a treat.

Using the XYZware you are very limited and I use slic3r and feel like im free haha can alter quite alot

Just been able to alter temperatures make a difference Immediately Also you can play around with feed rates

]]> Mon, 02 Mar 2015 22:32:22 +0000 https://www.soliforum.com/post/87948/#p87948 <![CDATA[Re: (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87933/#p87933 L.woinson95 wrote:

Are you using the same port on your PC? I know my printer only works in one port on my laptop before I changed over to Printing straight from the SD card

Edit: Just tried it with each USB port, no luck.

Did you switch to SD card printing just because it was easier or are there other benefits to it?

]]> Mon, 02 Mar 2015 21:23:19 +0000 https://www.soliforum.com/post/87933/#p87933 <![CDATA[Re: (Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87926/#p87926 Are you using the same port on your PC? I know my printer only works in one port on my laptop before I changed over to Printing straight from the SD card

]]> Mon, 02 Mar 2015 20:55:30 +0000 https://www.soliforum.com/post/87926/#p87926 <![CDATA[(Stock XYZWare issue) Device Not Found]]> https://www.soliforum.com/post/87922/#p87922 Hi all. A couple days ago I got my davinci 1.0 up and running. I did a small print Saturday night and didn't touch it yesterday. Today I went to go set a print to run but keep getting a "Device not found" error every time I click print.

I'm running completely stock firmware (1.1.J firmware). Have not updated XYZ (using the 1.1.29.4). I'm running Windows 8.1. Like I said though, it printed fine on Saturday without any special work arounds.

I tried uninstalling XYZ & the drivers and reinstalling. No luck.

Haven't been able to find anything on google, hoping somebody can help me here. Thanks.

]]> Mon, 02 Mar 2015 20:45:31 +0000 https://www.soliforum.com/post/87922/#p87922