<![CDATA[SoliForum - 3D Printing Community — Infill Rough Problem]]> https://www.soliforum.com/topic/10229/infill-rough-problem/ Mon, 09 Mar 2015 00:07:55 +0000 PunBB <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/88916/#p88916 Yes youre correct  - Z offset wrong way.

But it had a problem I wasnt aware of.

First off, the heated glass cracked.
While adjusting the bed, after a new glass,  had a prob w/ the RS adjuster.
The bed would adjust, but after a 2nd calibration it was off.
Removed the bed The threaded adjusting stud was loose.
Underneath, the nut that locks it into place had loosened out its holder.
Tighten all studs and locked w/ super glue.

Printed a 20mm box - perfect. No Z offset.

]]> Mon, 09 Mar 2015 00:07:55 +0000 https://www.soliforum.com/post/88916/#p88916 <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/87965/#p87965 Z offset is only for the start of the print.

]]> Mon, 02 Mar 2015 23:18:19 +0000 https://www.soliforum.com/post/87965/#p87965 <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/87961/#p87961 Are you sure the Z offset is for the first layer only?? Normally there's a separate one for the 1st layer also is the repetier firmware any good? Is there any links I could read up on it might want to flash my printer to that but unsure on it

]]> Mon, 02 Mar 2015 23:02:23 +0000 https://www.soliforum.com/post/87961/#p87961 <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/87947/#p87947 I run my filament at 240 degrees C and bed at 85 degrees C and seem to get really good results from it

]]> Mon, 02 Mar 2015 22:29:55 +0000 https://www.soliforum.com/post/87947/#p87947 <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/87927/#p87927 A negative Z offset means your nozzle is moving closer to the print bed to start with.  The smaller gap between the nozzle and the bed is causing material to be squeezed out, overlapping each other and causes lumps/clumps.  This goes away after the 2nd layer.

]]> Mon, 02 Mar 2015 21:00:27 +0000 https://www.soliforum.com/post/87927/#p87927 <![CDATA[Re: Infill Rough Problem]]> https://www.soliforum.com/post/87903/#p87903 Could it be your Z offset?? looking at that your nozzle would be 0.1mm in to your job which could cause it???

Just a suggestion I'm more clued up on CNC Milling so might be wrong.. only started this hobby of mine in November/December so still learning

]]> Mon, 02 Mar 2015 19:34:04 +0000 https://www.soliforum.com/post/87903/#p87903 <![CDATA[Infill Rough Problem]]> https://www.soliforum.com/post/87874/#p87874 The 1st layer of infill is rough, choppy, bumpy. The perimeters are smooth.
Subsequent infill layers drag thru, smoothing somewhat.
Top infill not as rough, 60 grit sandpaper rough. Perimeters are smooth.

DAV 1.0
Repetier FW
ABS
ABS Slurry
.3 layer ht - .35 1st layer ht
Bed- 110 / 110
Extruder- 223 /223
Ext Multiplier- 0.91
Speed- Infill- 35mm/s
Speed- Solid Infill- 30mm/s
Infill Extrusion Width- 90%
1st Layer Speed- 20mm/s
Z Offset-  -0.1 mm

Tried many different combos. Cant seem to correct it.

Any suggestions ?

]]> Mon, 02 Mar 2015 15:46:26 +0000 https://www.soliforum.com/post/87874/#p87874