I have everything except a few things.

Things I do not have

• Motherboard: Fried after shorted hot end and horrible repair job attempted

• 1 side handle cap: broken tab, other one is still fine

Things modded

• Extruder carriage: has cut out for e3d mod. Can still be used in stock configuration

• Hotend: Stock connector has been removed (bare wires) and thermistor cable resoldered back to jst connector from e3d mod.

Extras

• Extra set of stepper motors: One set is stock with stock extruder gear, the other is stock with the extruder gear removed and was used for mk7 and mk8 gears.

I've also got the LCD module around here somewhere (sans ribbon cable), I just can't find it at the moment.

Lemme know if you want to claim anything else! I'll sell both nozzles together for $80 + shipping if someone wants them both.

I'm pretty sure they thought they were scamming me because the printer was BADLY out of tune - drooping X belt, unleveled bed, ripped kapton tape, and a clogged nozzle. It obviously wasn't going to be printing a thing - but I got it home and after about 45 minutes I had it printing like a dream. I went from devastated over my broken Da Vinci to the happiest person in NJ in about 10 minutes flat.

Anywho, I'll post some pictures tomorrow of the remaining Da Vinci parts and mark off everything that's spoken for.

Cheers!
Andy

Congrats on your new steal of a deal too.

1. The unit is already totally disassembled. The frame is all taken apart into 3 piles - plastic shell pieces, metal frame pieces, and everything else (screws, bearings, etc).  So if you're not looking for a 1,000 piece puzzle to put back together, this might not be worth it to you. :-)

2. Just to re-state clearly, the motherboard, as far as I can determine, is dead. There's a hard short between the 3.3v line and ground that I haven't been able to track down. As far as I know, everything else should be fine.

3. I don't know what it would cost to ship a whole box full of the parts, but I know it'll be pretty darn expensive. When I got shipping quotes a few months ago when I was considering getting it repaired by XYZ, FedEx and UPS both wanted almost $200 to ship it (although granted, that was in a fully assembled state). My guess would be anywhere from $80-$150 to ship it now, plus whatever we'd decide is a fair price for the parts. Between that and the extensive time it'd take to reassemble the whole thing, it'd probably be a better buy to just get a new unit from Amazon.

4. Some of the plastic shell pieces have holes cut in them. The left side plastic shell and the top lid have both been cut up to allow for fan switches and external filament spools.

Thanks for the interest from everyone so far!

I'm interested in your bed assembly less the heater element/glass.

I would also like one of your oval windows if you're willing to sell just one?

Thanks,

John

I'm sure a lot of you saw the posts back when this happened, but I have a Da Vinci 1.0 that I shorted the motherboard on and fried. I was debating fixing it but I've since upgraded to a Powerspec 3D Pro (got it for an absolute STEAL at $460 for the floor model + two half-used spools of filament!!) and now there's no reason to go back to the Da Vinci.

I'm parting out the machine, so I have any and all parts available for cheap if you guys want 'em. Any steppers, assemblies, whatever you want. I have 2 nozzles - one is the stock one that came with the machine, the other is a brand new one I bought and added heatsinks to for PLA, and the 2 prints I ran it with worked like a charm.

Looking for $40+shipping for the original nozzle (and I'll throw in a couple copper heatsinks so you can sink it yourself for PLA), and $50+shipping for the new nozzle that's already sinked up.

Anything else, heated beds, rods, bearings, springs, carriages, motors, etc - just lemme know what you want and we can figure out a price.

Cheers!
Andy