<![CDATA[SoliForum - 3D Printing Community — Dremel Drill Press V1.0]]> 2014-08-29T06:11:01Z PunBB https://www.soliforum.com/topic/953/dremel-drill-press-v10/ <![CDATA[Re: Dremel Drill Press V1.0]]> is there an lock/holding screw to keep rack from moving due to vibration running Dremel?

]]> https://www.soliforum.com/user/795/ 2014-08-29T06:11:01Z https://www.soliforum.com/post/64805/#p64805 <![CDATA[Re: Dremel Drill Press V1.0]]> Just had mine partly break on a part I feared it might happen on. I had one of the shaft parts (just as it enters the pinion gear) sheer across the grain.

]]> https://www.soliforum.com/user/351/ 2013-02-17T04:45:29Z https://www.soliforum.com/post/12983/#p12983 <![CDATA[Re: Dremel Drill Press V1.0]]> Thanks caswal.

Mine will be a bit different but you have saved me a great deal of time, no doubt.

]]> https://www.soliforum.com/user/51/ 2013-02-16T22:48:11Z https://www.soliforum.com/post/12961/#p12961 <![CDATA[Re: Dremel Drill Press V1.0]]> The final 2 pieces.

The main carriage also uses an M6 Bolt and Nut to grip onto the 15mm PVC pipe used as the vertical rail/support.

]]> https://www.soliforum.com/user/351/ 2013-02-16T04:40:07Z https://www.soliforum.com/post/12917/#p12917 <![CDATA[Re: Dremel Drill Press V1.0]]> The Dremel holder has slots in the back of it, to connect it to the rack. I found these got a little misprinted (the overhangs are a little much), and were not quite wide enough so needed to dremel'd a little wider.

The Shim is a little cludge fix, that gets stuck to the back of the main carriage at the top. To keep the 15mm PVC pipe/carriage in alignment.

I would also integrate the Wheel, Wheel Connector Shaft, and Square Connector all as one piece, rather than 3 seperate pieces.

All of the fittings such as the shafts (both square and round) will need a little bit of a sand.

]]> https://www.soliforum.com/user/351/ 2013-02-16T04:35:55Z https://www.soliforum.com/post/12916/#p12916 <![CDATA[Re: Dremel Drill Press V1.0]]> Still havn't had time to fix these up like I want. So I'll just put the STL's up and list the couple of problems I had. This'll be spread over a couple of posts. As it is a lot of STL files.

]]> https://www.soliforum.com/user/351/ 2013-02-16T04:31:18Z https://www.soliforum.com/post/12915/#p12915 <![CDATA[Re: Dremel Drill Press V1.0]]> lawsy wrote:

Looks great, Are you going to release the STLs?

My drills and motors arrived yesterday.

Got a couple of things I want to adjust before I release the STL's. Things that I fixed with the dremel post print. Give me a day or 2.

]]> https://www.soliforum.com/user/351/ 2013-02-05T04:06:12Z https://www.soliforum.com/post/11864/#p11864 <![CDATA[Re: Dremel Drill Press V1.0]]> Looks great, Are you going to release the STLs?

My drills and motors arrived yesterday.

]]> https://www.soliforum.com/user/51/ 2013-02-05T02:57:04Z https://www.soliforum.com/post/11855/#p11855 <![CDATA[Re: Dremel Drill Press V1.0]]> cckens wrote:

Better yet, model a hole in the wheel (if possible, don't know the tolerances) and then make a spindle handle that locks in to the hole to allow you to spin the wheel via the handle.

Not a bad idea, will give it a go. (If I can can get the wheel off again, pretty tight push fit).

I'll get my DSLR and make a proper video tonight talking about it, and take it apart a bit more.

]]> https://www.soliforum.com/user/351/ 2013-02-05T00:48:08Z https://www.soliforum.com/post/11832/#p11832 <![CDATA[Re: Dremel Drill Press V1.0]]> Better yet, model a hole in the wheel (if possible, don't know the tolerances) and then make a spindle handle that locks in to the hole to allow you to spin the wheel via the handle.

]]> https://www.soliforum.com/user/129/ 2013-02-04T17:40:34Z https://www.soliforum.com/post/11764/#p11764 <![CDATA[Re: Dremel Drill Press V1.0]]> Nice!!! Caswal, So are you going to design a vice for the baseplate? ... maybe with a crossslide smile

]]> https://www.soliforum.com/user/296/ 2013-02-04T17:34:53Z https://www.soliforum.com/post/11763/#p11763 <![CDATA[Re: Dremel Drill Press V1.0]]> Great job caswal

]]> https://www.soliforum.com/user/78/ 2013-02-04T14:24:39Z https://www.soliforum.com/post/11751/#p11751 <![CDATA[Re: Dremel Drill Press V1.0]]> Very nicely done

]]> https://www.soliforum.com/user/134/ 2013-02-04T13:27:47Z https://www.soliforum.com/post/11745/#p11745 <![CDATA[Re: Dremel Drill Press V1.0]]> So got it all printed and working. Only needed to reprint 1 piece so far. Here are some photo's, will add some better ones when I get the DSLR back off my friend.

https://lh6.googleusercontent.com/-HizJPpWu3Mw/UQ-cEX61P2I/AAAAAAAABE4/APi95yJ8x-0/s720/P1000703.JPG

https://lh4.googleusercontent.com/-Jw78LVvZ9QI/UQ-b_Qj3_lI/AAAAAAAABEg/Fevu1Wk0GHw/s1280/P1000706.JPG

And a video if it in action:

]]> https://www.soliforum.com/user/351/ 2013-02-04T11:48:51Z https://www.soliforum.com/post/11740/#p11740 <![CDATA[Re: Dremel Drill Press V1.0]]> caswal wrote:

I finally have some time this weekend to actually print it.

Show us picture's when it's done. I could use a drill press myself at home.

]]> https://www.soliforum.com/user/7/ 2013-02-01T15:24:27Z https://www.soliforum.com/post/11352/#p11352