SoliForum - 3D Printing Community — First Layer height

Re: First Layer height

2015-02-28T12:52:40Z

I realise I was asking unconstructive qns, about the Nxxx and *X represent. pls ignor that.

I went back to do the Z-offset cal again, after selecting a new z-offset cal, and hitting set butt, the followings are the g-code ack outputs

C: M105
R: ok T:214.4 /0.0 B:89.9 /0.0 T0:214.4 /0.0 @:0 B@:0
C: M851 Z3.71
C: M500
C: M851 Z3.71
C: M500
R: echo:Z Offset: 3.71
ok
C: M105
R: echo:Settings Stored
ok
echo:Z Offset: 3.71
ok

so I guess M851 Z3.71 is to set a new z-offset and M500 is to save it to eeprom
I read somewhere in this community also, that the higher the Zx.xx, the closer it will bring the nozzle towards the bed.

Re: First Layer height

2015-02-28T11:52:48Z

thatdecade wrote:

Yes. The Z offset is stored in firmware. Changing the offset settings in soliprint will impact your runs in Repetier-Host.
The Z bed leveling must be done at the beginning of each print. Use gcode g29 in your repetier host start script after g28.
Exact instructions:

I issue M851 to my press afew times, it echoed different output all the time, except that Z Offset always show 4.01
anyone knows what Nxxx and *X represent what thing?

19:42:34.500 : N116 M851 *9
19:42:34.500 : echo:Z Offset: 4.01
19:43:13.843 : N153 M851 *8
19:43:13.843 : echo:Z Offset: 4.01
19:44:16.234 : N211 M851 *13
19:44:16.234 : echo:Z Offset: 4.01
19:44:37.046 : N231 M851 *15
19:44:37.046 : echo:Z Offset: 4.01

If the Z offset is setted near or at 0.00, will it bring my extruder nozzle closer or away from the bed?

Re: First Layer height

2015-01-23T16:53:06Z

Yes. The Z offset is stored in firmware. Changing the offset settings in soliprint will impact your runs in Repetier-Host.

The Z bed leveling must be done at the beginning of each print. Use gcode g29 in your repetier host start script after g28.
Exact instructions: http://www.soliforum.com/post/80457/#p80457

Re: First Layer height

2015-01-23T16:35:14Z

I'm pretty sure it saves it to firmware... If you keep the "printer settings" open while running the calibration, you can see the Gcode to verify.

Re: First Layer height

2015-01-23T16:31:20Z

is the z calibration a firmware setting or is it stored in soliprint? That is, if I do the z-calibration in soliprint, will it have any impact on a print using Repetier-Host?

Re: First Layer height

2015-01-23T16:27:40Z

Go to the Press getting started page on the Solidoodle site for info.

Re: First Layer height

2015-01-23T16:25:51Z

I agree with cptskippy, getting the z calibration right is very important for the z probing at the beginning of the print to work properly. Tweak the initial bed height position.

As for first layer height, that is in the slicer settings.
Options>Slic3r Options

Re: First Layer height

2015-01-23T16:18:07Z

Have you run the Z-Offset Calibration Utility?

First Layer height

2015-01-23T15:19:51Z

How on earth with 'soliprint' do you change the first layer height? It goes through the Z alignment, but then when it prints, its set so thin that all it does is back up the extruder.

I want to like this printer.. I love my SD2, SD3, and SD4. (I event like my RapMan3D on occasion)

Anyone?

Thanks.

I like Repetier, but Im trying to give this Soliprint a fair shot.