<![CDATA[SoliForum - 3D Printing Community — Repetier-Host Configuration]]> 2013-02-01T15:13:32Z PunBB https://www.soliforum.com/topic/911/repetierhost-configuration/ <![CDATA[Re: Repetier-Host Configuration]]> rdavidian28 wrote:

Is anyone using Repetier v83?  Seems to be many more config options for printer size, etc.  Is there a recommended settings guide for this?

Glad everything is up and running.

]]> https://www.soliforum.com/user/7/ 2013-02-01T15:13:32Z https://www.soliforum.com/post/11343/#p11343 <![CDATA[Re: Repetier-Host Configuration]]> Is anyone using Repetier v83?  Seems to be many more config options for printer size, etc.  Is there a recommended settings guide for this?

]]> https://www.soliforum.com/user/131/ 2013-01-28T18:54:00Z https://www.soliforum.com/post/10951/#p10951 <![CDATA[Re: Repetier-Host Configuration]]> Perlguy: Yeah, aside from the one compile error I documented, it worked great after I changed the baud rate.

]]> https://www.soliforum.com/user/35/ 2013-01-02T13:05:38Z https://www.soliforum.com/post/8278/#p8278 <![CDATA[Re: Repetier-Host Configuration]]> Got it working, thanks!  The only thing that I had to change was the baud rate.

]]> https://www.soliforum.com/user/142/ 2013-01-01T17:25:47Z https://www.soliforum.com/post/8260/#p8260 <![CDATA[Re: Repetier-Host Configuration]]> Should work. Frankly I only use Repetier. Pronterface seems primitive by comparison

]]> https://www.soliforum.com/user/35/ 2012-12-31T18:05:20Z https://www.soliforum.com/post/8220/#p8220 <![CDATA[Re: Repetier-Host Configuration]]> Thanks for that input :-) will Pronterface still work with it after recompile ? Or have you noticed any issue ? I just don't want to be stuck ;-)

]]> https://www.soliforum.com/user/590/ 2012-12-31T13:34:58Z https://www.soliforum.com/post/8215/#p8215 <![CDATA[Re: Repetier-Host Configuration]]> Atuor:

You have to recompile the firmware using the instructions from the Wiki to get Repetierhost to work. It will not work at 250000, and the out-of-the-box firmware only supports that speed. The process is pretty simple and straightforward though, and I did my best to explain it.

]]> https://www.soliforum.com/user/35/ 2012-12-31T13:25:13Z https://www.soliforum.com/post/8212/#p8212 <![CDATA[Re: Repetier-Host Configuration]]> Awesome, thanks for doing the wiki page!

From what I've done so far, it looks like I will only need to change the configuration.h file and change the baud-rate.  I've already changed my feed-rate in this file, so I am familiar with uploading it to the board.

I will give that a shot when I get home today.  Thank you again!

]]> https://www.soliforum.com/user/142/ 2012-12-31T13:11:02Z https://www.soliforum.com/post/8209/#p8209 <![CDATA[Re: Repetier-Host Configuration]]> Hi,
I have the same problem with my Solidoodle 2 received in december (so I suppose it's the latest firmware), works fine at 250000 bauds in Pronterface, but also get the same message as perlguy. Should I check the firmware ? recompile it or something ? looked at the wiki but I'm not sure what to do more, installed monodevelop and usermod thing, but still get the message  unknown, with xxx command waiting :-/

]]> https://www.soliforum.com/user/590/ 2012-12-31T12:38:05Z https://www.soliforum.com/post/8205/#p8205 <![CDATA[Re: Repetier-Host Configuration]]> Hi. I wrestled with Linux and Solidoodle and got it all working after about a week. Check the article I wrote for the Soliwiki: http://www.soliwiki.com/Linux

]]> https://www.soliforum.com/user/35/ 2012-12-31T03:11:43Z https://www.soliforum.com/post/8189/#p8189 <![CDATA[Re: Repetier-Host Configuration]]> "I am running on Ubuntu Linux."

Ian does not run Linux, afaik. There is a thread with links about how to get repetier running under Ubuntu,
along with explanations of -why-

Short version of the solution: You need to force a 112500 (I think) baud rate, as mono does not support non-standard rates. Yes, you need to change and update the firmware to fix this.

And don't forget to re-calibrate the PID when you do - it drove me nuts that the extruder started skipping after I got things set up.

]]> https://www.soliforum.com/user/257/ 2012-12-31T01:48:55Z https://www.soliforum.com/post/8185/#p8185 <![CDATA[Re: Repetier-Host Configuration]]> Did you give yourself serial com grp permissions?

]]> https://www.soliforum.com/user/106/ 2012-12-31T01:20:40Z https://www.soliforum.com/post/8180/#p8180 <![CDATA[Repetier-Host Configuration]]> I went through Ian's post on Repetier-Host configuration.

I can connect to the printer, but in "Manual Control" all I get is xx Command Waiting.

Under "Printer Information" I get:
  * Machine Type: unknown
  * Firmware:
  * Firmware URL:
  * Protocol:

From Ian's blog, it says that if I got my Solidoodle after mid October, I should not need to update my firmware.  I got mine in late November.

I am running on Ubuntu Linux.

What did I miss?

Do I need to actually install the Repetier firmware or something?

Thanks all!
Brent

]]> https://www.soliforum.com/user/142/ 2012-12-30T23:38:26Z https://www.soliforum.com/post/8175/#p8175