I'm hoping to write a summary up of things to help folk who are new to RH and 3d printing. I'll make a PDF of it if I do.
]]>carl_m1968 wrote:For the Repetier Da Vinci setup all the settings are stored in a fake EEPROM on the CD CARD. Those settings can be accessed by clicking CONFIG then EEPROM Configuration settings while yo uare connected to the printer. In that menu you will find all the values that make your printer run including temp settings. You can also access printer settings by clicking Printer settings over on the right. In there you will find the extruder and bed temps. Once you set them you have to exit Rephost and go back in. Then you will see the temps will show properly in the manual controls. You should make them the same as your slicer settings.
Hi I can't seem to get this to work. When I go to Config and then EEPROM Config, its greyed out. It says I'm connected but I don't see anything when I go to Printer info. Maybe this has something to do with how I flashed it? I got the firmware from user: bgm at the vovlito forums and then flashed it only using the XYZware. I disconnected the internet and selected the .bin file in the zip folder and then it worked. So I didn't use Arduino like many others did. Do you think this is a problem. Also, this problem is only the first in a long journey to getting Repetier to work safely and effectively because I'm completely new to Repetier Host.
Is there any step by step and easy to understand walkthrough to getting Repetier host working properly?
Try this, it is what I used..
]]>For the Repetier Da Vinci setup all the settings are stored in a fake EEPROM on the CD CARD. Those settings can be accessed by clicking CONFIG then EEPROM Configuration settings while yo uare connected to the printer. In that menu you will find all the values that make your printer run including temp settings. You can also access printer settings by clicking Printer settings over on the right. In there you will find the extruder and bed temps. Once you set them you have to exit Rephost and go back in. Then you will see the temps will show properly in the manual controls. You should make them the same as your slicer settings.
Hi I can't seem to get this to work. When I go to Config and then EEPROM Config, its greyed out. It says I'm connected but I don't see anything when I go to Printer info. Maybe this has something to do with how I flashed it? I got the firmware from user: bgm at the vovlito forums and then flashed it only using the XYZware. I disconnected the internet and selected the .bin file in the zip folder and then it worked. So I didn't use Arduino like many others did. Do you think this is a problem. Also, this problem is only the first in a long journey to getting Repetier to work safely and effectively because I'm completely new to Repetier Host.
Is there any step by step and easy to understand walkthrough to getting Repetier host working properly?
]]>For the Repetier Da Vinci setup all the settings are stored in a fake EEPROM on the CD CARD. Those settings can be accessed by clicking CONFIG then EEPROM Configuration settings while yo uare connected to the printer. In that menu you will find all the values that make your printer run including temp settings. You can also access printer settings by clicking Printer settings over on the right. In there you will find the extruder and bed temps. Once you set them you have to exit Rephost and go back in. Then you will see the temps will show properly in the manual controls. You should make them the same as your slicer settings.
THIS!
]]>I was following Jake's setup guide here: http://voltivo.com/forum/davinci-peersu … s-printing
After the hot manual leveling, it said I could check the settings with auto, but I guess what I did wrong was saving at that point.
Thanks again!
]]>I did manual leveling with a playing card, followed by automatic leveling using the machine interface with Repetier 0.91 RC1 (luc). After the auto leveling, it came up with a 3-point average distance value of 0.14 and I did a Store to EEPROM. The 0.14 is now what Z is listed as after I home. Do I need to wipe this out or give this value to my host (S3D)?
Thanks
If you followed the manual process then you should not have run auto cal afterwards. That defeats the process, go and reread the process and then follow it to the letter. From where you are now just count this as your stored pass and repeat the manual process from that point with paper, not a playing card.
By the way if you did this hot as you are supposed to then playing cards have a coating on them that could get on your nozzle and cause issues. There is a reason the process specifies paper, or preferably a feeler gauge but paper is close enough.
]]>Thanks
]]>I can look at the settings in curaengine and understand how to save them now (I wasn't doing that properly before.) I still can't get a good print. It just moves the extruder all over the glass bed.
Can someone help me by providing their repetier host settings and whether they are using manual or autoleveling?
Thanks!
It not like a trade secret, so here are my Repetier EEPROM settings.
Description Value
Baudrate 256000
Filament Printed [m] 364.627
Printer active [s] 1151332
Max. Inactive time [ms,0=off] 0
Stop stepper after inactivity [ms,0=off] 360000
X-axis steps per mm 80
Y-axis steps per mm 80
Z-axis steps per mm 2600
X-axis max. feedrate [mm/s] 200
Y-axis max. feedrate [mm/s] 200
Z-axis max. feedrate [mm/s] 5
X-axis homing feedrate [mm/s] 40
Y-axis homing feedrate [mm/s] 40
Z-axis homing feedrate [mm/s] 4
Max. jerk [mm/s] 25
Max. Z-jerk [mm/s] 0.3
X home position [mm] -30
Y home position [mm] -13
Z home position [mm] -3.05
X max. length [mm] 240
Y max. length [mm] 215
Z max. length [mm] 230
X backlash [mm] 0
Y backlash [mm] 0
Z backlash [mm] 0
X-axis acceleration [mm/s^2] 1200
Y-axis acceleration [mm/s^2] 1200
Z-axis acceleration [mm/s^2] 100
X-axis travel acceleration [mm/s^2] 1200
Y-axis travel acceleration [mm/s^2] 1200
Z-axis travel acceleration [mm/s^2] 100
Z-probe height [mm] 40
Max. z-probe – bed dist. [mm] 10
Z-probe speed [mm/s] 2
Z-probe x-y-speed [mm/s] 150
Z-probe offset x [mm] 0
Z -probe offset y [mm] 0
Z-probe X1 20
Z-probe Y1 20
Z-probe X2 160
Z-probe Y2 20
Z-probe X3 100
Z-probe Y3 160
Autolevel active (1/0) 0
Bed Heat Manager [0-3] 2
Bed PID drive max. 255
Bed PID drive min. 80
Bed PID P-gain 196
Bed PID I-gain 33
Bed PID D-gain 290
Bed PID max. value [0-255] 255
Extr. 1 steps per mm 96
Extr. 1 max. feedrate [mm/s] 50
Extr. 1 start feedrate [mm/s] 20
Extr. 1 acceleration [mm/s^2] 5000
Extr. 1 Heat Manager [0-3] 3
Extr.1 PID drive max. 230
Extr. 1 PID drive min. 40
Extr. 1 PID P-gain 7
Extr. 1 PID I-gain 2
Extr. 1 PID D-gain 40
Extr. 1 PID max. value [0-255] 255
Extr. 1 X-offset [steps] 0
Extr. 1 Y-offset [steps] 0
Extr. 1 temp. stabilize time [s] 537329665
Extr. 1 temp. for retraction when heating [c] 537329814
Extr. 1 distance to retract when heating [mm] 537329664
Extr.1 extruder cooler speed [0-255] 255
Extr. 1 advance K [0=off] 0
Extr. 1 advance L [0=off] 0
I only use manual leveling as auto sets the incorrect values even though the machine shows a pass. The values are too high for proper printing.
]]>Can someone help me by providing their repetier host settings and whether they are using manual or autoleveling?
Thanks!
]]>Does someone have some settings they can share?
]]>
You had it figured it out too, so thanks!
Can you point me to a default configuration for RH? The one that comes with it is not for the da vinci and I'm not sure what to put for limits etc.
I tried to change the default bed temperature from 50C to 85C to print ABS, and when I run the slicer, it keeps generating the default 50 value. Do you have any ideas?
]]>I have flashed the firmware to repeiter host v 0.92alpha without issue. I am able to use the front buttons without issue and can get the bed to heater, load filament, perform auto calibration, etc.
I downloaded Repetier Host 1.06. I have RH saying its connected to the printer, but then I can't get anything to work.
- I do a show printer info and it says "unknown machine" and has blanks for everything except 1 extruder.
- The temperature on the bottom of the GUI never shows the extruder temperature
- When I load a 3d stl file and slice it, things appear fine. When I hit print, nothing happens. I tried to preheat the bed and extruder, but it still does nothingI had no issue printing the demo objects before I flashed the firmware. I never ran xyzware, since I didn't want to mess with any of their junk.
I'm using the linux version of RH.
Please help!
Do you have the comport speed setting under printer settings set for the same speed that the printer is set for?
]]>I downloaded Repetier Host 1.06. I have RH saying its connected to the printer, but then I can't get anything to work.
- I do a show printer info and it says "unknown machine" and has blanks for everything except 1 extruder.
- The temperature on the bottom of the GUI never shows the extruder temperature
- When I load a 3d stl file and slice it, things appear fine. When I hit print, nothing happens. I tried to preheat the bed and extruder, but it still does nothing
I had no issue printing the demo objects before I flashed the firmware. I never ran xyzware, since I didn't want to mess with any of their junk.
I'm using the linux version of RH.
Please help!
]]>