SoliForum - 3D Printing Community — Repetier Host 1.06 printing issues

Re: Repetier Host 1.06 printing issues

2014-12-29T21:32:01Z

Checked connections (as I was getting the extruder heat error earlier), not running through a hub, and am fairly certain that the port is free. I also set it up for the SD2 for sure.

I have tried so many settings that I have had to go in, uninstall and wipe everything (including registry() and then reinstall again to make sure I am only tweaking a couple of things.

I am trying to get a complete copy of the settings in another thread but so far no one is coming forward with a set. This seems to be my only hope at this point.

Re: Repetier Host 1.06 printing issues

2014-12-29T15:01:17Z

also any other serial port connected devices on computer can conflict with com port and may have to assign higher numbered port to 3D printer.

plus did you go into the new version of RH and setup that printer. most versions install with a default printer like an SD3 or? set print area sizes etc.

Re: Repetier Host 1.06 printing issues

2014-12-28T14:25:36Z

make sure your not running the USB through a hub or extender.

Re: Repetier Host 1.06 printing issues

2014-12-28T13:51:46Z

Make sure that all connectors on the board are connected in right places and
contacted tightly. Since you changed RH version, so compare the all settings
With another user.

Re: Repetier Host 1.06 printing issues

2014-12-28T13:42:56Z

Check the settings with another user, then also check connctors and wires of the hot end.

Re: Repetier Host 1.06 printing issues

2014-12-28T12:28:55Z

Make sure your baud rate and comport is correct.

Re: Repetier Host 1.06 printing issues

2014-12-28T03:09:27Z

Thanks for the idea. I just tried three different cables and they all do the same thing. If I disconnect the printer then I can hit OK in the manual controls and get the number of commands down to one but I can never get the printer connected and any activation.

If I had any hair left I would be pulling it out right now. I got my printer on the 28th of November and have yet to print a complete model.

Perhaps someone can send me settings or something? I am so lost.

Re: Repetier Host 1.06 printing issues

2014-12-28T01:49:26Z

Have you tried replacing the USB cable. Have seen previously replacing the cable fixes the commands waiting issue.

Re: Repetier Host 1.06 printing issues

2014-12-28T01:09:51Z

So this "Command Waiting" thing is jsut killing me. Even when I change the version it maintains the number of commands waiting. Any thoughts anyone?

Re: Repetier Host 1.06 printing issues

2014-12-28T00:56:44Z

Can you post the start code?

Re: Repetier Host 1.06 printing issues

2014-12-28T00:40:32Z

Okay so I just did the exact same thing with another computer running windows 7 ultimate (i7 / 6GB ram) and it did the exact same thing so I am completely stumped now.

bummer

Re: Repetier Host 1.06 printing issues

2014-12-27T23:55:15Z

That's a good idea. I will go get another laptop and bring it in and try that now.

Re: Repetier Host 1.06 printing issues

2014-12-27T23:46:10Z

I have somewhat similar symptoms on my SD3, except its my heated bed that wont heat up.

http://www.soliforum.com/topic/8728/pri … -midprint/

Could you try another pc/system?

Re: Repetier Host 1.06 printing issues

2014-12-27T23:40:53Z

I appreciate the reply.

I am on a Solidoodle 2. It doesn't take a lot of time to heat up when it does. IT seems as though there is a backlog of commands that don't fire or something.

EDIT: Currently it says 27 commands waiting.

Re: Repetier Host 1.06 printing issues

2014-12-27T23:34:38Z

What printer do you have?I have used RH 1.06 on win 8.1 on my SD3 with no issues. Maybe check the heater wires for looseness since it takes so long to heat.;