<![CDATA[SoliForum - 3D Printing Community — Baudrate?]]> 2014-12-17T07:44:31Z PunBB https://www.soliforum.com/topic/8767/baudrate/ <![CDATA[Re: Baudrate?]]> arturnoole163 wrote:

Mine is 250000. I chose it from this thread (voltivo.com/forum/davinci-firmware/148-your-configuration) and it seems to work just fine, although, I have only been on repertere firmware since last night so I don't know about long term.


My first one or two runs where ok as well. It was only a bit later I started having issue. It also seems a fresh boot and reload of Rep host helps as well. I will play around with it. I was running 250000 as well and that was where issues started. I am now down to 128000 and so far so good.

]]> https://www.soliforum.com/user/7731/ 2014-12-17T07:44:31Z https://www.soliforum.com/post/75564/#p75564 <![CDATA[Re: Baudrate?]]> arturnoole163 wrote:

Mine is 250000. I chose it from this thread (voltivo.com/forum/davinci-firmware/148-your-configuration) and it seems to work just fine, although, I have only been on repertere firmware since last night so I don't know about long term.


Mi first one or two runs where ok as well. It was only a bit later I started having issue. It also seems a fresh boot and reload of Rep host helps as well. I will play around with it. I was running 250000 as well and that was where issues started. I am now down to 128000 and so far so good.

]]> https://www.soliforum.com/user/7731/ 2014-12-17T07:44:20Z https://www.soliforum.com/post/75563/#p75563 <![CDATA[Re: Baudrate?]]> Mine is 250000. I chose it from this thread (voltivo.com/forum/davinci-firmware/148-your-configuration) and it seems to work just fine, although, I have only been on repertere firmware since last night so I don't know about long term.

]]> https://www.soliforum.com/user/7943/ 2014-12-17T06:37:18Z https://www.soliforum.com/post/75557/#p75557 <![CDATA[Re: Baudrate?]]> So am I the only one here using the Repetier Firmware? I would have thought more would be and could tell me their baud rate.

]]> https://www.soliforum.com/user/7731/ 2014-12-17T03:17:41Z https://www.soliforum.com/post/75548/#p75548 <![CDATA[Baudrate?]]> What baudrate is everyone using.  Especially those that have made the switch to Repetier firmware. I keep having a problem with the printer just stopping at some point during the print. It seems to be linked to mu baudrate in the fact the higher I set it the sooner it stops. I know the issue is communication related as I can print from the SD card all day long and for any length of time wit no issue. 

This actually does not apply to those using stock firmware. On stock you actually print from the SD card as well. It just uploads the file to the printer over USB. On stock you could disconnect the USB at any time during printing and it would continue until complete. Try the Repetier and the ptint will stop as data is sent from the host to the printer and processed in teal time.

In my case it seems almost like Rephost is just shoving the data to the printer rather it acknowledges or not and once Rephost sees it has sent all the data it just stops the printer. That does not make since though because the way I inderstand the operation, it is FIFO in the buffer so no later commands can ever be processed before the current commands get processed.

So any clues what might be causing my prints to stop and it seems to be related to baudrate? Just wanted to ask what rate others use.

]]> https://www.soliforum.com/user/7731/ 2014-12-16T09:16:13Z https://www.soliforum.com/post/75408/#p75408