<![CDATA[SoliForum - 3D Printing Community — Cant figure out connection issue]]> 2014-11-20T19:56:39Z PunBB https://www.soliforum.com/topic/8402/cant-figure-out-connection-issue/ <![CDATA[Re: Cant figure out connection issue]]> Awesome!  You are very welcome!

]]> https://www.soliforum.com/user/131/ 2014-11-20T19:56:39Z https://www.soliforum.com/post/72515/#p72515 <![CDATA[Re: Cant figure out connection issue]]> all of the settings were correct.  I changed out a USB cord and it worked fine.  Dont always understand it but it is working now. Thanks for the help and tips

]]> https://www.soliforum.com/user/4946/ 2014-11-20T19:43:29Z https://www.soliforum.com/post/72508/#p72508 <![CDATA[Re: Cant figure out connection issue]]> ok thanks will post back to see what happens

]]> https://www.soliforum.com/user/4946/ 2014-11-20T18:49:25Z https://www.soliforum.com/post/72499/#p72499 <![CDATA[Re: Cant figure out connection issue]]> Did it get anywhere with the actual print?

That seems like a request for a missed line number...connection issue?

At this point I would suggest checking baud rate settings and your USB connections and then consider swapping the cable.

http://wiki.solidoodle.com/repetier-hos … on-windows

]]> https://www.soliforum.com/user/131/ 2014-11-20T18:01:08Z https://www.soliforum.com/post/72490/#p72490 <![CDATA[Re: Cant figure out connection issue]]> I am now getting a resend 1474 message.

]]> https://www.soliforum.com/user/4946/ 2014-11-20T17:28:14Z https://www.soliforum.com/post/72483/#p72483 <![CDATA[Re: Cant figure out connection issue]]> Sounds a bit similar to this topic (although this was the bed heater waiting to get up to heat and failing):

http://www.soliforum.com/topic/8293/hel … it-starts/

Can you post a printout of your Slic3r GCODE?

]]> https://www.soliforum.com/user/131/ 2014-11-20T16:01:34Z https://www.soliforum.com/post/72476/#p72476 <![CDATA[Re: Cant figure out connection issue]]> It runs the extruder to the middle and the plate touchs and then it goes back to the starting spot and says it completed the print

]]> https://www.soliforum.com/user/4946/ 2014-11-20T15:49:54Z https://www.soliforum.com/post/72473/#p72473 <![CDATA[Re: Cant figure out connection issue]]> Does it actually begin to print (extrude) and just stop?

]]> https://www.soliforum.com/user/131/ 2014-11-20T14:58:59Z https://www.soliforum.com/post/72467/#p72467 <![CDATA[Re: Cant figure out connection issue]]> didnt have any errors.  I ended up using another power supply and it worked.  Now it runs like it is going to print and doesnt finish it. 
Love figuring out one thing and then fixing something else.

i have two machines  I have had a belt broke when I got them, an x motor went bad and now a power supply in less than a year.

]]> https://www.soliforum.com/user/4946/ 2014-11-20T14:55:34Z https://www.soliforum.com/post/72466/#p72466 <![CDATA[Re: Cant figure out connection issue]]> Does the bed actually heat up for a while?

Are you getting any errors in the Log screen at the bottom of RH?  Like asking you to use M999 to reset?

]]> https://www.soliforum.com/user/131/ 2014-11-19T20:18:48Z https://www.soliforum.com/post/72386/#p72386 <![CDATA[Re: Cant figure out connection issue]]> Just found out when I go to heat the print bed It stops working.

]]> https://www.soliforum.com/user/4946/ 2014-11-19T20:11:30Z https://www.soliforum.com/post/72385/#p72385 <![CDATA[Cant figure out connection issue]]> When I go to the repetier host I can conncet to my printer.  I can even get the all of the axis to move.  Once I heat the extruder and the bed I cant do anything.  It just keeps adding up commands no matter how long I wait.

]]> https://www.soliforum.com/user/4946/ 2014-11-19T20:02:15Z https://www.soliforum.com/post/72384/#p72384