<![CDATA[SoliForum - 3D Printing Community — SD4 top layer infill issues]]> 2014-10-16T02:33:09Z PunBB https://www.soliforum.com/topic/8002/sd4-top-layer-infill-issues/ <![CDATA[Re: SD4 top layer infill issues]]> It's very odd that the steps per mm would be off on X or Y, but if you check in RH under EEPROM Settings, it should give you the current values and allow you to adjust them.  Not at my machine, but I think the default for both X and Y is 88 unless they have changed to GT2 pulleys...

If they both are reading the same, I would investigate vref and belt tightening as wardjr stated above...

]]> https://www.soliforum.com/user/131/ 2014-10-16T02:33:09Z https://www.soliforum.com/post/68797/#p68797 <![CDATA[Re: SD4 top layer infill issues]]> There is also just adjusting the steps per mm on the Y axis. Might want to check that before fiddling with belts or vref. I know when I first got my solidoodle, the default values were considerably off for both X and Y.

]]> https://www.soliforum.com/user/270/ 2014-10-16T01:40:51Z https://www.soliforum.com/post/68796/#p68796 <![CDATA[Re: SD4 top layer infill issues]]> .5mm left to right, probably tighten the x belt or check that your nozzle is secure.
Past that you're adjusting VREF for that stepper.

]]> https://www.soliforum.com/user/2291/ 2014-10-16T00:14:04Z https://www.soliforum.com/post/68787/#p68787 <![CDATA[Re: SD4 top layer infill issues]]> IronMan wrote:
saqueeb wrote:

I reclaibrated to .48 on my open cube walls, infill seems much better, but my 10x 10 cube is still only 9.55mm on the x axis. Y is 10 exactly.

how can i adjust the x axis?

What infill?  Your open cube should have Zero infill and 1 perimeter, and the wall thickness goal is .48...is this how you printed it?


sorry, infill is now fine, but my 10x10 cube is only 9.55mm on the x axis and 10mm on the y. it should be 10 on each.

]]> https://www.soliforum.com/user/7419/ 2014-10-15T23:40:00Z https://www.soliforum.com/post/68779/#p68779 <![CDATA[Re: SD4 top layer infill issues]]> saqueeb wrote:

I reclaibrated to .48 on my open cube walls, infill seems much better, but my 10x 10 cube is still only 9.55mm on the x axis. Y is 10 exactly.

how can i adjust the x axis?

What infill?  Your open cube should have Zero infill and 1 perimeter, and the wall thickness goal is .48...is this how you printed it?

]]> https://www.soliforum.com/user/131/ 2014-10-15T23:01:54Z https://www.soliforum.com/post/68774/#p68774 <![CDATA[Re: SD4 top layer infill issues]]> wardjr wrote:

Lets start with your perfect calibration.  You have a .40 nozzle and need to be shooting for .48 not .42 so dial that in first.
Should just be a simple extrusion multiplier change.  Then, what axis measures at the 9.5 on your cube?

I reclaibrated to .48 on my open cube walls, infill seems much better, but my 10x 10 cube is still only 9.55mm on the x axis. Y is 10 exactly.

how can i adjust the x axis?

]]> https://www.soliforum.com/user/7419/ 2014-10-15T22:44:57Z https://www.soliforum.com/post/68773/#p68773 <![CDATA[Re: SD4 top layer infill issues]]> yes thats started with intro to SD3 and the newer SD2 .4 orifice. mine still has the smaller orifice .35 that .42 was for

]]> https://www.soliforum.com/user/795/ 2014-10-15T18:57:20Z https://www.soliforum.com/post/68757/#p68757 <![CDATA[Re: SD4 top layer infill issues]]> wardjr wrote:

Correct

Thanks i will make those changes this afternoon.

]]> https://www.soliforum.com/user/7419/ 2014-10-15T18:07:24Z https://www.soliforum.com/post/68750/#p68750 <![CDATA[Re: SD4 top layer infill issues]]> Correct

]]> https://www.soliforum.com/user/2291/ 2014-10-15T17:58:00Z https://www.soliforum.com/post/68749/#p68749 <![CDATA[Re: SD4 top layer infill issues]]> wardjr wrote:

Really, I am working on updating the WIKI right now.
Don't forget to change your extrusion width's in your slice profile.

change them to .48 and not .42 correct?

]]> https://www.soliforum.com/user/7419/ 2014-10-15T17:49:22Z https://www.soliforum.com/post/68747/#p68747 <![CDATA[Re: SD4 top layer infill issues]]> Really, I am working on updating the WIKI right now.
Don't forget to change your extrusion width's in your slice profile.

]]> https://www.soliforum.com/user/2291/ 2014-10-15T16:40:32Z https://www.soliforum.com/post/68744/#p68744 <![CDATA[Re: SD4 top layer infill issues]]> wardjr wrote:

Lets start with your perfect calibration.  You have a .40 nozzle and need to be shooting for .48 not .42 so dial that in first.
Should just be a simple extrusion multiplier change.  Then, what axis measures at the 9.5 on your cube?


really? .48?

i thought for some reason it was .42, but i can make the change very easily this afternoon, and then i will reprint the 10x10 cube and report back the results.

thank you very much!

]]> https://www.soliforum.com/user/7419/ 2014-10-15T16:18:29Z https://www.soliforum.com/post/68743/#p68743 <![CDATA[Re: SD4 top layer infill issues]]> Lets start with your perfect calibration.  You have a .40 nozzle and need to be shooting for .48 not .42 so dial that in first.
Should just be a simple extrusion multiplier change.  Then, what axis measures at the 9.5 on your cube?

]]> https://www.soliforum.com/user/2291/ 2014-10-15T15:06:30Z https://www.soliforum.com/post/68731/#p68731 <![CDATA[SD4 top layer infill issues]]> so i have got my new E3DV6 installed and extruding correctly. my hollow cube wall thicknesses are .42 exactly.

but i am having a couple issues.

1. my top layers are not filling 100% the tops do not meet up with the perimeters at all times. ( see picture)

2. my 10mm x 10mm test cubes are 10mm on 2 sides and 9.5mm on the other 2 sides. what is causing this?

my extruderis correctly calibrated and i have tensioned my belts evenly.

thanks

]]> https://www.soliforum.com/user/7419/ 2014-10-15T15:03:57Z https://www.soliforum.com/post/68729/#p68729