<![CDATA[SoliForum - 3D Printing Community — z-axis lead screw replacement]]> 2012-12-27T16:02:59Z PunBB https://www.soliforum.com/topic/793/zaxis-lead-screw-replacement/ <![CDATA[Re: z-axis lead screw replacement]]> cckens wrote:

The frame is strong enough to hold quite a bit of weight.

Enough to stand on, I got a chuckle out of that engadget sd3 video, who stands on their printer while printing? Its strong for that but the base floor is thin and flimsy. When i get mine i think i'll put a 1/4" or 3/8" thick sheet of aluminum on the floor, make some cutouts for the z-rods, secure it with some bolts and attach the z-motor to it.
Otherwise a forged lead screw should solve this issue.

]]> https://www.soliforum.com/user/178/ 2012-12-27T16:02:59Z https://www.soliforum.com/post/8026/#p8026 <![CDATA[Re: z-axis lead screw replacement]]> I was also thinking of replacing the threaded Z rod (and keeping my existing motor).  How exactly is the rod attached into the motor?  Is it just press-fit to the motor shaft?  I see someone mentioned using 2x nuts, are they saying to screw them down till they press against the motor body itself and force the rod out?  (I have the new/improved design with no coupler)

I am planning on replacing it with a high-precision metric threaded rod, obviously this would involve adjusting the firmware/EEPROM setting for Z steps per mm but I assume this would be the same basic technique as the extruder calibration (tell it to go 100mm, measure the actual travel, then calculate the difference)?

]]> https://www.soliforum.com/user/498/ 2012-12-27T04:48:20Z https://www.soliforum.com/post/8006/#p8006 <![CDATA[Re: z-axis lead screw replacement]]> As I said, mine was rather severe.  Printing a couple of calibration objects and you can pinpoint a few problems and this is one of them.  You can also see a few signs of a bent lead screw without even printing.

The video here (http://www.soliforum.com/topic/672/zaxi … er-wobble/) shows the base flex that you get.  The stepper is screwed onto sheet metal so some flex is expected.  Run the z-axis down 100mm and then home it. If you see the top of the screw wobble outside a couple of mm you'll see problems when you print.  I did.

Can't tell you how thick the base is, but it looks like all sides are 1.25mm thick.  The frame is strong enough to hold quite a bit of weight.

]]> https://www.soliforum.com/user/129/ 2012-12-27T03:42:31Z https://www.soliforum.com/post/8000/#p8000 <![CDATA[Re: z-axis lead screw replacement]]> My printer should be here next week, i hope i won't run into this issue. If i will you can bet the sd3 will have the same issue since its the exact same design.
Tell me how thick is the bottom panel that the z-motor is attached to, is it thin and flimsy and bends easily?

]]> https://www.soliforum.com/user/178/ 2012-12-27T03:06:45Z https://www.soliforum.com/post/7999/#p7999 <![CDATA[Re: z-axis lead screw replacement]]> I received mine in early November, so mine is not part of the early batches.  However, this can conceivably happen in newer AND older machines as well.  The degree that I encountered was more severe than is normally seen in any of the models.  Replacing the lead screw seemed to be the best (and most cost effective) option.  Solidoodle provided the lead screw (free of charge) but I had to pay for the shipping.  Fair trade.

]]> https://www.soliforum.com/user/129/ 2012-12-27T02:37:57Z https://www.soliforum.com/post/7997/#p7997 <![CDATA[Re: z-axis lead screw replacement]]> Is this z-wobble issue only found on early printers only or on every single one being produced now?

]]> https://www.soliforum.com/user/178/ 2012-12-27T02:16:11Z https://www.soliforum.com/post/7994/#p7994 <![CDATA[Re: z-axis lead screw replacement]]> Just replaced the z-axis lead screw.  Took 3 nuts to pop that thing off as they had it really firm on the motor.  Only had some basic superglue, but it seemed to have done the trick... (more on that one in a bit...)

Replaced everything, re-leveled the bed and started a print.  Went with the hinge piece that showed the banding so well in the past. Result shown below.  On the right we have the original lead screw print, on the left the new one.

http://www.kenzden.com/download/PartCompare-a.jpg

As you can see, there's still some banding, but it's minimal at best, and could be caused by backlash.  At this point I grabbed the jam nut and attached it to the lead screw.  figured that if it could hold for a bit, I'd try a couple of small prints to get a better view...

Not so good.  I ran the gcode and all of a sudden on a z-home I heard the grinding of the motor then a kind of spinning sound, but no movement on the z.  The superglue had popped and the screw is spinning on the motor.  Now I get to do it all over again, this time with some better adhesive and maybe a bit more grease.

BUT!!!  I know that the lead screw has solved most of my issue with the prints

]]> https://www.soliforum.com/user/129/ 2012-12-27T01:53:51Z https://www.soliforum.com/post/7992/#p7992 <![CDATA[Re: z-axis lead screw replacement]]> jefferysanders wrote:

It is easier than it looks/sounds. I have been taking mine apart all week testing different backlash solutions that I have been printing.

I look forward to reading about that. I hope you'll be sharing on the forums ^_^?

]]> https://www.soliforum.com/user/192/ 2012-12-15T03:22:31Z https://www.soliforum.com/post/7183/#p7183 <![CDATA[Re: z-axis lead screw replacement]]> It is easier than it looks/sounds. I have been taking mine apart all week testing different backlash solutions that I have been printing.

]]> https://www.soliforum.com/user/106/ 2012-12-15T00:12:01Z https://www.soliforum.com/post/7168/#p7168 <![CDATA[Re: z-axis lead screw replacement]]> You would need to remove the bed, but you don't have to take it out of the printer beyond the reach of its wires.  Loosen the hose clamps on the guide rods and slide them out the top or bottom until the bed comes free.  Then you can move it to where there is room to unscrew the threaded rod from it.

http://solidoodletips.files.wordpress.com/2012/09/photo-29.jpg

]]> https://www.soliforum.com/user/14/ 2012-12-14T23:35:44Z https://www.soliforum.com/post/7167/#p7167 <![CDATA[Re: z-axis lead screw replacement]]> Would I need to remove the bed too?  Or would removing the endstop and then unscrewing the rod be easier?  Or even feasible?  Don't want to do too much to it, but don't want to gank the thing into non-working status...

]]> https://www.soliforum.com/user/129/ 2012-12-14T23:25:29Z https://www.soliforum.com/post/7165/#p7165 <![CDATA[Re: z-axis lead screw replacement]]> Unscrew the Z motor from the bottom of the case.  Then the whole assembly can duck under the y rod.

]]> https://www.soliforum.com/user/14/ 2012-12-14T19:36:06Z https://www.soliforum.com/post/7147/#p7147 <![CDATA[Re: z-axis lead screw replacement]]> I can... no worries on that part... then I'll have the rest of the weekend to play!

]]> https://www.soliforum.com/user/129/ 2012-12-14T19:19:19Z https://www.soliforum.com/post/7146/#p7146 <![CDATA[Re: z-axis lead screw replacement]]> I will be doing this write up tomorrow with some other things if you can wait till then.

]]> https://www.soliforum.com/user/13/ 2012-12-14T19:18:18Z https://www.soliforum.com/post/7145/#p7145 <![CDATA[z-axis lead screw replacement]]> Anyone have any idea the steps necessary to replace this?  I received mine last night (sans any instructions) and on looking at it, it doesn't seem too obvious the steps you have to take to get this thing into place.

I see the bed attached, but the y-axis pulley system seems to preclude removing the bed without removing it first.

Any suggestions would be appreciated.

]]> https://www.soliforum.com/user/129/ 2012-12-14T19:14:56Z https://www.soliforum.com/post/7144/#p7144