<![CDATA[SoliForum - 3D Printing Community — Another Case & Printer Mod - Updated]]> 2013-12-09T20:52:46Z PunBB https://www.soliforum.com/topic/4562/another-case-printer-mod-updated/ <![CDATA[Re: Another Case & Printer Mod - Updated]]> It's not the heat that's the issue it's the golden rod that absorbs moisture
that will cause the oil to dry

]]> https://www.soliforum.com/user/2779/ 2013-12-09T20:52:46Z https://www.soliforum.com/post/43732/#p43732 <![CDATA[Re: Another Case & Printer Mod - Updated]]> I use high temp lubriplate.
http://www.lubriplate.com/Products/Mult … -Temp.aspx

]]> https://www.soliforum.com/user/187/ 2013-12-09T20:50:41Z https://www.soliforum.com/post/43731/#p43731 <![CDATA[Re: Another Case & Printer Mod - Updated]]> Yeah it will take it a while to dry it up, just be sure to add oil from time to time so it
doesn't cause you grief later on.

]]> https://www.soliforum.com/user/2779/ 2013-12-09T19:54:01Z https://www.soliforum.com/post/43723/#p43723 <![CDATA[Re: Another Case & Printer Mod - Updated]]> techbuilder2175 wrote:

I am using a golden rod in there too to keep my nylon and everything else dry.

Oooo I wouldn't do that if I were you
Your going to dry up the oil on the rods

I can add more oil when needed. Not a problem!

I haven't thought of that though. haha! Thanks!

]]> https://www.soliforum.com/user/1682/ 2013-12-09T19:51:09Z https://www.soliforum.com/post/43719/#p43719 <![CDATA[Re: Another Case & Printer Mod - Updated]]>

I am using a golden rod in there too to keep my nylon and everything else dry.

Oooo I wouldn't do that if I were you
Your going to dry up the oil on the rods

]]> https://www.soliforum.com/user/2779/ 2013-12-09T19:07:11Z https://www.soliforum.com/post/43710/#p43710 <![CDATA[Re: Another Case & Printer Mod - Updated]]> Hey dubbs, looks good and I like that you are adding a switch to the encasement.  Always found it a pain in the tail to unplug the 'doodle when it was done.  Looking forward to seeing it finished!

]]> https://www.soliforum.com/user/2252/ 2013-12-09T18:53:12Z https://www.soliforum.com/post/43702/#p43702 <![CDATA[Re: Another Case & Printer Mod - Updated]]> Very nice!
Make more spool holders. You will want more! Trust me!

I have two spool holders in my case. I am using a golden rod in there too to keep my nylon and everything else dry.


http://i.imgur.com/BuDS3ID.jpg

]]> https://www.soliforum.com/user/1682/ 2013-12-09T14:31:09Z https://www.soliforum.com/post/43677/#p43677 <![CDATA[Re: Another Case & Printer Mod - Updated]]> I have started mounting the electronics.

http://pipbc.com/images/ec1.jpg

]]> https://www.soliforum.com/user/187/ 2013-12-07T14:19:56Z https://www.soliforum.com/post/43542/#p43542 <![CDATA[Another Case & Printer Mod - Updated]]> I am in the process of modding my SD3 & at the rate I am going it might be done at Christmas.

here is a list of my mods i have planned (I already have components)
1. new case

2. Power supply

3.  Azteeg X3 Full Featured 3D Printer Controller v1.1 [Connectors:Screw Terminals [Terminal Blocks] Soldered][Expansion Shield:v1.1 Cover Shield w/ 2 thermocouple inputs][Stepper Drivers:5pcs SD8825 w/ Heatsink]

4. Helios 200 Heat Bed 12V

5. Endstops &   Epcos 100k Thermistors

6. E3d Hotend

I will keep this updated

Case sides made of .060" (16 Ga sheet metal)

http://pipbc.com/images/outside.jpg

]]> https://www.soliforum.com/user/187/ 2013-11-16T20:08:10Z https://www.soliforum.com/post/41758/#p41758