<![CDATA[SoliForum - 3D Printing Community — Repetier Host not controlling 3d printer]]> 2015-10-23T14:26:25Z PunBB https://www.soliforum.com/topic/4560/repetier-host-not-controlling-3d-printer/ <![CDATA[Re: Repetier Host not controlling 3d printer]]> Check your baudrates.

]]> https://www.soliforum.com/user/9121/ 2015-10-23T14:26:25Z https://www.soliforum.com/post/108187/#p108187 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Was having this issue:

Make sure the baud rates are set the same in "configuration.h" and the "printer settings" in Repetier.

You guys have probably solved it already however smile

]]> https://www.soliforum.com/user/12383/ 2015-10-23T02:30:34Z https://www.soliforum.com/post/108143/#p108143 <![CDATA[Re: Repetier Host not controlling 3d printer]]> I'm just gonna throw something here different ...

    How about your Printer PORT settings ?

]]> https://www.soliforum.com/user/9919/ 2015-06-19T13:12:59Z https://www.soliforum.com/post/99446/#p99446 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Try using this version of Marlin. It is preconfigured for a Da vinci 1.0 and RAMPS 1.4 with LCD but should get you in the ball park.

]]> https://www.soliforum.com/user/7731/ 2015-06-06T20:40:27Z https://www.soliforum.com/post/98158/#p98158 <![CDATA[Re: Repetier Host not controlling 3d printer]]> same problem. anyone have the answer?

]]> https://www.soliforum.com/user/7268/ 2015-06-06T20:25:51Z https://www.soliforum.com/post/98157/#p98157 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Are you getting any errors in RH such as max temp or cold extrusion prevented?

]]> https://www.soliforum.com/user/2291/ 2015-04-25T16:35:04Z https://www.soliforum.com/post/94139/#p94139 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Did you get anywhere with this issue? I have the same. Communications is working and and Repetier will drive the all the motors correctly to their Home position and respond to the end stop switched-, but no control is coming form the manual controller. Very strange....Im using Arduino Mega 2560/ Ramps 1.4/ Repetier 1.0.6 and marlin firmware-

]]> https://www.soliforum.com/user/10597/ 2015-04-25T13:02:43Z https://www.soliforum.com/post/94122/#p94122 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Hi Cummings,
I've found the same problem. Any solution so far?

]]> https://www.soliforum.com/user/5776/ 2014-05-04T00:39:24Z https://www.soliforum.com/post/55624/#p55624 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Whenever I connect using sprinter and Prontra face everything works perfect. However whenever I upload Marlin as the firmware it won't work with Prontorface or RH. This suggests to me that it is in the Marlin firmware settings. I have set the configuration.h file for motherboard 33.  I believe the problem lies within the pins.h file. That would explain any thermistor errors or motor control errors. For the time being sprinter works fine with Prontorface. However I don't get the benefit of using an LCD reader.

]]> https://www.soliforum.com/user/4064/ 2013-11-17T23:36:31Z https://www.soliforum.com/post/41849/#p41849 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Check your thermistor.. Make sure it's connected properly, not sorted, and reading temp (assuming you can still connect).

Trying homing RH if you are able to get it to connect.

]]> https://www.soliforum.com/user/815/ 2013-11-17T22:18:58Z https://www.soliforum.com/post/41845/#p41845 <![CDATA[Re: Repetier Host not controlling 3d printer]]> O.K.  So after working on this all day with some expert programmers, we are all still stumped.  I am using a Ramps 1.4 board on an Arduino Mega 2560 r3 board.  The 3d printer is a Prusa Mendel I3. 

Sprinter works fine with Pronterface, but no LCD capability.

I tried Repetier with Repetier Host, but the motors don't respond. 
Next, I tried Marlin v1 with Repetier and Pronterface.  Same thing - motors not working.  I get an error message in Pronterface:  : Extruder switched off. MAXTEMP triggered !
Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)

I get the Repetier Host error:  Error: checksum mismatch, Last Line: 3 and so on.

Any suggestions??

]]> https://www.soliforum.com/user/4064/ 2013-11-17T22:01:34Z https://www.soliforum.com/post/41844/#p41844 <![CDATA[Re: Repetier Host not controlling 3d printer]]> Define SDSS is on line 341 in the pins.h

]]> https://www.soliforum.com/user/644/ 2013-11-17T14:15:45Z https://www.soliforum.com/post/41803/#p41803 <![CDATA[Re: Repetier Host not controlling 3d printer]]> I had to turn off the (new?) reset on connect printer settings to get past anything but commands waiting.

]]> https://www.soliforum.com/user/3054/ 2013-11-17T02:13:37Z https://www.soliforum.com/post/41786/#p41786 <![CDATA[Re: Repetier Host not controlling 3d printer]]> "There are some pin differences between Marlin and Repetier firmwares.  I 'm not by my printer at this point but check the pins.h file.  I think the #define X, Y + Z max_pin's in pins.h should all be set to -1 and dfine SDSS should be 25 for Ramps/Arduino mega boards"

Where is the define SDSS statement?

]]> https://www.soliforum.com/user/4064/ 2013-11-17T01:14:58Z https://www.soliforum.com/post/41782/#p41782 <![CDATA[Re: Repetier Host not controlling 3d printer]]> There are some pin differences between Marlin and Repetier firmwares.  I 'm not by my printer at this point but check the pins.h file.  I think the #define X, Y + Z max_pin's in pins.h should all be set to -1 and dfine SDSS should be 25 for Ramps/Arduino mega boards

]]> https://www.soliforum.com/user/644/ 2013-11-16T23:23:50Z https://www.soliforum.com/post/41771/#p41771