<![CDATA[SoliForum - 3D Printing Community — suport material]]> 2014-02-16T11:21:55Z PunBB https://www.soliforum.com/topic/4503/suport-material/ <![CDATA[Re: suport material]]> If you calibrate the extruder, adjust the bed and enter these settings, you should get good prints. At least I did. I had to lower infill extrusion width to .4 and set flow rate to 0.95 and it is all good!

]]> https://www.soliforum.com/user/219/ 2014-02-16T11:21:55Z https://www.soliforum.com/post/49899/#p49899 <![CDATA[Re: suport material]]> i have kiss slicer downloaded and intergrated to Rhost i just cant get my head around those settings its all screwy to me after Slic3r..

ill give it another try

]]> https://www.soliforum.com/user/2211/ 2014-02-16T00:28:29Z https://www.soliforum.com/post/49858/#p49858 <![CDATA[Re: suport material]]> Thank you so much for these settings! The printer is printing flawlessly now!

The problem was the setting for firmware: 5D Relative E and Absolute E. I set it to absolute E and the extruder jumping stopped.

]]> https://www.soliforum.com/user/219/ 2014-02-15T13:05:42Z https://www.soliforum.com/post/49806/#p49806 <![CDATA[Re: suport material]]> never mind fixed the problem

]]> https://www.soliforum.com/user/3698/ 2013-11-20T03:14:56Z https://www.soliforum.com/post/42002/#p42002 <![CDATA[Re: suport material]]> im calibrating the flow rate now,
printing a test box, that has an open top

after it does its two bottom layers it does about 6 perimeter layers then after that, it goes to infill again,
my box was created 40x40x40 mm hollow with a 3 mm wall thickness.

any ideas?

]]> https://www.soliforum.com/user/3698/ 2013-11-20T02:57:56Z https://www.soliforum.com/post/42001/#p42001 <![CDATA[Re: suport material]]> The extruder stepper calibration is only for RH.

The flow rate calibration can be done in slic3r/RH and then use that number in the flow tweak of Kisslicer. This flow rate calibration should be done with every different roll of ABS/PLA you put on because each roll will have its own difference.

]]> https://www.soliforum.com/user/3491/ 2013-11-13T02:13:22Z https://www.soliforum.com/post/41525/#p41525 <![CDATA[Re: suport material]]> then I wont have to modify that part for kisslicer again correct?

just the filament extrusion.

]]> https://www.soliforum.com/user/3698/ 2013-11-13T01:52:47Z https://www.soliforum.com/post/41523/#p41523 <![CDATA[Re: suport material]]> yup. measure the difference. calculate the percentage its off. multiply times what the current number is in EEPROM. Enter new number. Save. Then test again.

]]> https://www.soliforum.com/user/3491/ 2013-11-13T01:12:08Z https://www.soliforum.com/post/41518/#p41518 <![CDATA[Re: suport material]]> muddtt wrote:

Should do calibration of extruder stepper first. Then flow rate. Theres a menu in RH now for eeprom settings that make it easier to change the numbers.

I don't have to do anything special with the reset button on repetier right?
I can just measure the filament and how much its using and compare to the what it should.
change the numbers to what they need to be and save to EEPROM right?

]]> https://www.soliforum.com/user/3698/ 2013-11-13T01:08:29Z https://www.soliforum.com/post/41517/#p41517 <![CDATA[Re: suport material]]> Should do calibration of extruder stepper first. Then flow rate. Theres a menu in RH now for eeprom settings that make it easier to change the numbers.

]]> https://www.soliforum.com/user/3491/ 2013-11-12T15:17:12Z https://www.soliforum.com/post/41465/#p41465 <![CDATA[Re: suport material]]> muddtt wrote:

Filament settings tab. You should have calibrated this once upon a time

http://www.soliwiki.com/Calibration_of_the_flow_rate
And
http://www.soliwiki.com/Calibration_of_ … on_stepper
Are both very important.

yeah I never did that,
uh oh,
probably could get some even more amazing print quality if I did this huh?

]]> https://www.soliforum.com/user/3698/ 2013-11-12T10:15:53Z https://www.soliforum.com/post/41445/#p41445 <![CDATA[Re: suport material]]> Filament settings tab. You should have calibrated this once upon a time

http://www.soliwiki.com/Calibration_of_the_flow_rate
And
http://www.soliwiki.com/Calibration_of_ … on_stepper
Are both very important.

]]> https://www.soliforum.com/user/3491/ 2013-11-12T06:01:45Z https://www.soliforum.com/post/41442/#p41442 <![CDATA[Re: suport material]]> found it.

]]> https://www.soliforum.com/user/3698/ 2013-11-12T06:01:02Z https://www.soliforum.com/post/41441/#p41441 <![CDATA[Re: suport material]]> muddtt wrote:

Well first things i'd input would be your filament diameter. Then "flow tweak" would be your extrusion multiplier in slic3r.

And yes, the speed tweaks are controlled in the speed tab

where in slic3r would I fine the "extrusion multiplier"? just so I know im printing about the same as I was with slic3r, because kisslicer is looking kinda weak, and is stringy kinda.

]]> https://www.soliforum.com/user/3698/ 2013-11-12T05:53:19Z https://www.soliforum.com/post/41439/#p41439 <![CDATA[Re: suport material]]> Well first things i'd input would be your filament diameter. Then "flow tweak" would be your extrusion multiplier in slic3r.

And yes, the speed tweaks are controlled in the speed tab

]]> https://www.soliforum.com/user/3491/ 2013-11-12T05:49:10Z https://www.soliforum.com/post/41437/#p41437