SoliForum - 3D Printing Community — Extrusion Temp Very High - 223 C, Calibration Problems?

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-09-01T00:58:16Z

Problem Solved. It turns out my thermistor was probably measuring just fine. I ended up building my own all metal hot end and since I put it in, I can extrude easily at 185 C. I haven't had a problem at all. The hotend I built was actually pretty cheap using common materials from the hardware store. I am going to post it in the "hacks and mods" section when I get a chance to compile the info. Thanks for all of your help!

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T17:26:38Z

Hey ne14pez, a couple things.

If you perform the PID Tune then you won't have crazy temperature swings that shutdown the system.
http://www.soliwiki.com/PID_tuning

Also, to see what temps you should be extruding at, try manually extruding 100mm of filament at 10-20mm/s into the air. Start with your temps at 205-210 and look for teeth marks in the extruded filament (you might have to tighten the tentioner arm a little. Keep bumping up the temps by 2-3C until the teeth marks go away.

If all else fails then you can change the max_temp in the firmware.

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T16:06:33Z

at this point, I just want to be able to lower the thermistor temp read by 5 degrees. I'm just sick of my print stopping because it reached 230. I don't care if I toast my hotend, it doesn't work at any other temps anyway (and I'm in the process of machining an all metal hotend without a plastic PEEK). How do I do that?

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T15:43:16Z

Since I don't have that setup, is there another way I can estimate if my temps are way off, and is there a way to correct for it in the software? For example, After I do a thorough cleaning of the nozzle and barrel and try to extrude for the first time, I can't get it to even melt the ABS at any temp lower than like 200, and even there, it's just barely melting it. Is this a clear indication that the temps are off?

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T15:03:58Z

It's better to use a K type thermocouple with a multimeter and sticking under the kapton next to the thermistor.

http://solidoodletips.wordpress.com/201 … mperature/

Re: Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T14:31:36Z

IR thermometer is a box of lies for this sort of thing. Emissivity, spot ratio, etc.

Extrusion Temp Very High - 223 C, Calibration Problems?

2013-08-30T14:23:05Z

My stock hotend clogged on day 1 and I broke it trying to fix it so I machined a new barrel from steel. I've gotten very good at taking it out, unclogging (using heat, acetone, etc.). Now I can only get it to extrude at very high temps like 220-225. I believe my thermistor is not reading correct values. When it shows 223, it is really around 195. My IR thermometer shows a 30-40C difference in temp (Repetier says 220, IR thermometer says 175).

I've gotten parts to print at these temps, but the problem is 1) I am worried that I am running it too hot, 2) I often hit the 230C mark and my printer shuts down.

I've done PID tuning a couple times as well. Is there a way to calibrate the thermistor readings?