<![CDATA[SoliForum - 3D Printing Community — Really BAD owl]]> 2013-08-11T05:30:19Z PunBB https://www.soliforum.com/topic/3453/really-bad-owl/ <![CDATA[Re: Really BAD owl]]> here we go this is re along the lines of what im expecting, much beter layers no gaps. .1 , 20% fill, print failed with an hour left to go. damnit.

]]> https://www.soliforum.com/user/2211/ 2013-08-11T05:30:19Z https://www.soliforum.com/post/32551/#p32551 <![CDATA[Re: Really BAD owl]]> installes a well nut trying to see if there was any difference in my prints...

the owl on the left is befor the well nut the owl on the right is after

little more consistent but still little horizontal gaps on my perimeters

]]> https://www.soliforum.com/user/2211/ 2013-08-07T20:53:59Z https://www.soliforum.com/post/32238/#p32238 <![CDATA[Re: Really BAD owl]]> It's a do it yourself mod, the community solutions are giving better results than the SD solution at the moment.  Try the slop nut solution first, it is simple and effective.  Don't chase perfection if you don't need it.  I have mine stock and it's perfectly fine for my use so I haven't done a thing to it.

]]> https://www.soliforum.com/user/78/ 2013-08-07T20:53:20Z https://www.soliforum.com/post/32237/#p32237 <![CDATA[Re: Really BAD owl]]> Honestly, even if they replace it, it will only be marginally better.  http://www.soliforum.com/post/31960/#p31960

They acknowledge that there are several issues causing banding. I think you best bet is to pick a fix from the forums and run with it. I have had wonderful success with my slop nut design using M5 threaded rod. I am sure M3 works well also.

]]> https://www.soliforum.com/user/1906/ 2013-08-07T00:37:54Z https://www.soliforum.com/post/32150/#p32150 <![CDATA[Re: Really BAD owl]]> is the banding something i should bring to solidoodles attention? or is that pretty much a users problem? ive been planning to do either a ball screw or the fine threaded rod mod  so i guess just say f-it and bring on the mod

]]> https://www.soliforum.com/user/2211/ 2013-08-07T00:33:12Z https://www.soliforum.com/post/32148/#p32148 <![CDATA[Re: Really BAD owl]]> What speed are you running that at? It would help to slow it down a little bit. Also, I know that you have some fairly severe banding. --> http://www.soliforum.com/topic/3434/torture-test-print/

I think the combination of the 2 is what you are seeing here

]]> https://www.soliforum.com/user/1906/ 2013-08-07T00:08:45Z https://www.soliforum.com/post/32147/#p32147 <![CDATA[Re: Really BAD owl]]> much better still not perfect though what tweeks do I need to make ?

]]> https://www.soliforum.com/user/2211/ 2013-08-06T22:38:41Z https://www.soliforum.com/post/32131/#p32131 <![CDATA[Re: Really BAD owl]]> yep i tried to print the yoda lite to at 40% scale.  i have a feeling its to fast and theres something else going on too i dont know what tho


UPDATE: my Z ofset was way off. brought it up re leveled gonna try the owl again

]]> https://www.soliforum.com/user/2211/ 2013-08-06T03:57:11Z https://www.soliforum.com/post/32038/#p32038 <![CDATA[Re: Really BAD owl]]> Well I gotta say I have never seen the owl look like that.....


Is that the same slicer profile as your other print ?

]]> https://www.soliforum.com/user/296/ 2013-08-06T03:34:03Z https://www.soliforum.com/post/32037/#p32037 <![CDATA[Really BAD owl]]> so I tried to print an owl form thingiverse and it didn't come out so well

.3mm layer height,4 perimeters, perimeter speed 35 mm along small perimeters. sliced with slic3r

whats wrong here ?

other prints are okay
http://www.soliforum.com/misc.php?actio … mp;preview

]]> https://www.soliforum.com/user/2211/ 2013-08-06T02:54:58Z https://www.soliforum.com/post/32036/#p32036