<![CDATA[SoliForum - 3D Printing Community — extruder fan design that fits the Solidoodle 3 extruder]]> 2013-07-30T15:48:43Z PunBB https://www.soliforum.com/topic/3358/extruder-fan-design-that-fits-the-solidoodle-3-extruder/ <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> Hmm will wait and see. Maybe I will design my own fan mount smile

Here is the parts for the enclosure that I made smile

Hmm could not post link here on Soliforun (anyone know whats up with that!?)

However it is part or thing:125599

BR / kajaken

]]> https://www.soliforum.com/user/2573/ 2013-07-30T15:48:43Z https://www.soliforum.com/post/31432/#p31432 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> kajakmannen wrote:

@2n2r5: in the comment on that extruder fan someone is asking for a mod to fit the square hot end so I understand it as it does not fit squat hot end. Can someone verify that it works? Also does it mount to the acrylic stock extruder assembly or do I need to mot it?

@mcbride19: I made it in SW. It turned out great and uses one sheet of (4x400x600mm) acrylic sheet and three sheets of (2x300x300mm) acrylic sheet and some m3 screws. I will uploade parts to thingiverse in a couple of days.

I have the square hotend and it worked for me. It mounts to the stock extruder assembly but you will need magnets.

The one thing that I did run into with this fan is that it would melt a bit of how close it was to the hotend.

]]> https://www.soliforum.com/user/1906/ 2013-07-30T12:30:49Z https://www.soliforum.com/post/31403/#p31403 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> @2n2r5: in the comment on that extruder fan someone is asking for a mod to fit the square hot end so I understand it as it does not fit squat hot end. Can someone verify that it works? Also does it mount to the acrylic stock extruder assembly or do I need to mot it?

@mcbride19: I made it in SW. It turned out great and uses one sheet of (4x400x600mm) acrylic sheet and three sheets of (2x300x300mm) acrylic sheet and some m3 screws. I will uploade parts to thingiverse in a couple of days.

]]> https://www.soliforum.com/user/2573/ 2013-07-30T11:23:51Z https://www.soliforum.com/post/31398/#p31398 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> Very nice enclosure, where did you get the suypport for it ?

]]> https://www.soliforum.com/user/2127/ 2013-07-30T04:34:43Z https://www.soliforum.com/post/31385/#p31385 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> http://www.thingiverse.com/thing:30828 works pretty well.

]]> https://www.soliforum.com/user/1906/ 2013-07-30T04:03:51Z https://www.soliforum.com/post/31382/#p31382 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> Found quit many extruder fan designs on thingiverse but unclear if they work with stock extruder (acrylic see through one) and square hot end.

]]> https://www.soliforum.com/user/2573/ 2013-07-29T23:42:06Z https://www.soliforum.com/post/31361/#p31361 <![CDATA[Re: extruder fan design that fits the Solidoodle 3 extruder]]> http://lmgtfy.com/?q=solidoodle+fan+design&l=1  :-P

Nice Enclosure! With the above link, also see lawsy's design

]]> https://www.soliforum.com/user/1906/ 2013-07-29T22:38:02Z https://www.soliforum.com/post/31357/#p31357 <![CDATA[extruder fan design that fits the Solidoodle 3 extruder]]> Hi anyone that knows of a extruder fan design that fit to the stock extruder on the Solidoodle 3.
It has the square hot end.

Any ideas.

Have finally gotten my SD3 to work as it should. Made my own enclosure which turned out great.

]]> https://www.soliforum.com/user/2573/ 2013-07-29T22:31:49Z https://www.soliforum.com/post/31355/#p31355