<![CDATA[SoliForum - 3D Printing Community — More Pictorial Schematic for Filastruder]]> 2013-09-30T04:38:20Z PunBB https://www.soliforum.com/topic/2983/more-pictorial-schematic-for-filastruder/ <![CDATA[Re: More Pictorial Schematic for Filastruder]]> I Would like to add that I have built SESTOS Variant C diagram Wiring ) Autostart, Cold extrusion not possible, Fan starts with Motor.

Followed the SESTOS instruction on the bottom of the BETA.pdf file you provided.

This wiring works great, one switch to turn on and everything is on Auto, good work.


olaf wrote:

I'm with the instructions for the Sestos Controller.
Since I have no hardware ,once please
check pages 5-8

Olaf

]]> https://www.soliforum.com/user/3331/ 2013-09-30T04:38:20Z https://www.soliforum.com/post/37693/#p37693 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> I'm with the instructions for the Sestos Controller.
Since I have no hardware ,once please
check pages 5-8

Olaf

]]> https://www.soliforum.com/user/2495/ 2013-07-02T22:45:16Z https://www.soliforum.com/post/28815/#p28815 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> IanJohnson wrote:

There are instructions with the PID, but the English is fairly broken so its a bit of a challenge to figure out.

Yup, I see what you mean.

Operation Procedures:
1/ Press SET key 2 second into the function mode, after return to the operation mode. If no any change
after 10 second automatic return.
2/ For temperature setting, press the UP or Down key change the value, after 10 second operate the new
setting.
3/ First operate the Auto adjustment, press AT key 2 second, SV display blink AT, finally into PID control
mode. Press the AT key 2 second to abandon Auto adjustment.
4/ If successful the first Auto adjustment, can not use AT key for Auto adjustment again. It need change
function setting Ctrl to 2 to operated again.
5/Auto adjustment needs from few second to few hour.
Suggestions:
1/ If use SSR or SCR for control part, setting control period prefer 4 second or shorter.
2/ If use relay for control part, setting control period prefer 20 second or longer for extend the relay life.

"the English is fairly broken" is an under statement.

But I guess others have gotten it to work so hopefully I'll manage.

Ralph

]]> https://www.soliforum.com/user/1424/ 2013-07-02T21:54:29Z https://www.soliforum.com/post/28812/#p28812 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Here's the PDF: http://www.sestos-hk.com/english/download/d1s-en.pdf

Thanks again!

]]> https://www.soliforum.com/user/221/ 2013-07-02T18:03:21Z https://www.soliforum.com/post/28786/#p28786 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Hi Tim,

If I knew on which pins of Sestos PID "alarm" is,
I could complete the schematics  for these variants

]]> https://www.soliforum.com/user/2495/ 2013-07-02T17:58:00Z https://www.soliforum.com/post/28784/#p28784 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Nice!

Keep in mind, this is only for the Mypin variant.

]]> https://www.soliforum.com/user/221/ 2013-07-02T17:33:03Z https://www.soliforum.com/post/28780/#p28780 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Add Minimum PID Settings

]]> https://www.soliforum.com/user/2495/ 2013-07-02T17:22:56Z https://www.soliforum.com/post/28777/#p28777 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> So no one has done a translation/English reprint?

Ralph

]]> https://www.soliforum.com/user/1424/ 2013-07-01T13:42:52Z https://www.soliforum.com/post/28631/#p28631 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> There are instructions with the PID, but the English is fairly broken so its a bit of a challenge to figure out.

]]> https://www.soliforum.com/user/14/ 2013-07-01T01:22:40Z https://www.soliforum.com/post/28559/#p28559 <![CDATA[Re: More Pictorial Schematic for Filastruder]]>

You need to hold down the set button until "AL1" is displayed

Aren't there instructions that explain this?

Ralph

]]> https://www.soliforum.com/user/1424/ 2013-07-01T00:55:05Z https://www.soliforum.com/post/28555/#p28555 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Thanks, that did it. You need to hold down the set button until "AL1" is displayed, then you can set a temp to control the alarm switch.

]]> https://www.soliforum.com/user/1426/ 2013-06-30T23:07:51Z https://www.soliforum.com/post/28547/#p28547 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> If the AL light doesn't come on, the controllers alarm is likely set wrong. You have to set a temperature to turn the motor on.

]]> https://www.soliforum.com/user/221/ 2013-06-30T19:57:35Z https://www.soliforum.com/post/28514/#p28514 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> I wired my machine according to the variant C schematic. When I power the circuit the PID turns on and I configure a target temperature. The nozzle heats up, and there is the red current temperature setting rises.

The motor and fan never seem to turn on, I'm not sure if this is a function of the PID (controlling the ALARM switch) a problem with the wiring or some configuration with the PID unit.

The PID makes a clicking sound and the OUT1 LED turns on and off (toggling power to the heating element, I guess?). No other LEDs turn on.

Has anyone else seen this? Any idea what I'm missing?

]]> https://www.soliforum.com/user/1426/ 2013-06-30T19:09:49Z https://www.soliforum.com/post/28507/#p28507 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> Thanks Olaf, this was very helpful.

]]> https://www.soliforum.com/user/1426/ 2013-06-29T02:34:26Z https://www.soliforum.com/post/28352/#p28352 <![CDATA[Re: More Pictorial Schematic for Filastruder]]> olaf wrote:

Hi Tim ,

I ask for galvanic Isolation to protect the PID Controller.

In another project, I have destroyed a controller
because 12V came indirectly to the Termocoupe (via Chassis)

For the moment I put Kaptontape between Brass an Thermocoupe   

Have a nice Weekend

Olaf

I'll let you know as soon as I know!

]]> https://www.soliforum.com/user/221/ 2013-06-28T20:45:09Z https://www.soliforum.com/post/28308/#p28308