<![CDATA[SoliForum - 3D Printing Community — Just stupid?]]> 2013-06-28T00:36:44Z PunBB https://www.soliforum.com/topic/2909/just-stupid/ <![CDATA[Re: Just stupid?]]> Are you cooling your electronics? A fan on the Spain board may eliminate these issues. Don't forget to unplug your printer from the USB when you turn your printer power supply off. I leave my computer on 24/7 and leaving the USB plugged into the printer keeps the main board on. That wil, generate heat. That can be disapated with a fan.

]]> https://www.soliforum.com/user/46/ 2013-06-28T00:36:44Z https://www.soliforum.com/post/28212/#p28212 <![CDATA[Re: Just stupid?]]> solidoodlesupport wrote:
wolfy454 wrote:

ok, so was printing and then burp,..... it stopped M999
code?

Get it working?

Yes I did!  I been Learning new stuff everyday..   BUT just got the M999 code again today, but this was after a lot of printing smile.

]]> https://www.soliforum.com/user/2426/ 2013-06-27T22:16:03Z https://www.soliforum.com/post/28201/#p28201 <![CDATA[Re: Just stupid?]]> wolfy454 wrote:

ok, so was printing and then burp,..... it stopped M999
code?

Get it working?

]]> https://www.soliforum.com/user/7/ 2013-06-24T22:22:12Z https://www.soliforum.com/post/27785/#p27785 <![CDATA[Re: Just stupid?]]> Right out of the box my slicing at .1mm and .2mm failed because of there is somewhere in the config that it thinks thinks the number is not actually a number.  .3mm slices fine though.

You can check your logs and see it says something like "argument {blah} got an error in multiplication" or something like that.

I still have not figured out what causes that, but for now .3mm config works fine.

]]> https://www.soliforum.com/user/2234/ 2013-06-24T18:05:16Z https://www.soliforum.com/post/27764/#p27764 <![CDATA[Re: Just stupid?]]> It lost it's connection to the thermistor, which reads the temperature in the extruder.  Check the connector on the extruder (blue one?) and make sure it is plugged in on the board.  I think it is at the top, a small connector with a "T" on it.  If the connections are good, it is possible that they didn't install it right and caused a short.

The thermistor is a small glass bead with a couple of wires coming out.  The wires have insulation which is just a small tube that slides over them.  If the insulation slides up a little, then the bare wire can touch the brass nozzle and keep it from working right.  I would check for that unless you have some 1/4" kapton tape on hand to tape the thermisor back on to the nozzle when you are done.

Aside from that you would need to check the wires with a multimeter to make sure there isn't a break somewhere.

]]> https://www.soliforum.com/user/14/ 2013-06-22T06:52:27Z https://www.soliforum.com/post/27499/#p27499 <![CDATA[Re: Just stupid?]]> ok, so was printing and then burp,..... it stopped M999
code?

]]> https://www.soliforum.com/user/2426/ 2013-06-22T05:35:48Z https://www.soliforum.com/post/27495/#p27495 <![CDATA[Re: Just stupid?]]> you can move it around and rotate it 3d in the 'object placement' tab in Repetier.

]]> https://www.soliforum.com/user/296/ 2013-06-22T05:10:36Z https://www.soliforum.com/post/27493/#p27493 <![CDATA[Re: Just stupid?]]> HAHAHA SOUNDS LIKE PAC-MAN!

]]> https://www.soliforum.com/user/2426/ 2013-06-22T05:09:06Z https://www.soliforum.com/post/27492/#p27492 <![CDATA[Re: Just stupid?]]> ok lol hit home and all good!

THANKS SO MUCH!

]]> https://www.soliforum.com/user/2426/ 2013-06-22T05:08:12Z https://www.soliforum.com/post/27491/#p27491 <![CDATA[Re: Just stupid?]]> It worked!  Just is not sticking!  that is a easy fix, I guess??

It started at the very end on the heat pad and was drawing off the side, almost

Can I center it?

I know this is a auto load program, but seems to far over

]]> https://www.soliforum.com/user/2426/ 2013-06-22T05:03:44Z https://www.soliforum.com/post/27489/#p27489 <![CDATA[Re: Just stupid?]]> Ok, I sliced it to 3mm after rotating x 90, it made 42 layers took 40.669 sec to slice no errors... running it through virtual printer right now seems to work...??? I would check your slicer config files or better yet post up the gcode of what it slices for you.

]]> https://www.soliforum.com/user/296/ 2013-06-22T04:59:23Z https://www.soliforum.com/post/27486/#p27486 <![CDATA[Re: Just stupid?]]> back

]]> https://www.soliforum.com/user/2426/ 2013-06-22T04:48:46Z https://www.soliforum.com/post/27485/#p27485 <![CDATA[Re: Just stupid?]]> everything I want to print, even after netfabb rework, still says the same thing.  Once it is sliced I hit print and instantly says job done.

going to reboot the pc.

BRB

Thanks!

]]> https://www.soliforum.com/user/2426/ 2013-06-22T04:44:31Z https://www.soliforum.com/post/27484/#p27484 <![CDATA[Re: Just stupid?]]> ronsii wrote:

could you post up the file you are trying to get to work?


Here it is.

]]> https://www.soliforum.com/user/2426/ 2013-06-22T04:40:18Z https://www.soliforum.com/post/27483/#p27483 <![CDATA[Re: Just stupid?]]> elmoret wrote:
wolfy454 wrote:

Every thing is hot and ready to go, it says "idle"  Once I hit run, it says "Finished"

Are you slicing the STL file? There's a big fat button "Slice with Slic3r".

The big fat one and the small one

]]> https://www.soliforum.com/user/2426/ 2013-06-22T04:39:19Z https://www.soliforum.com/post/27482/#p27482