<![CDATA[SoliForum - 3D Printing Community — Ceramic head ?]]> 2013-06-25T08:05:10Z PunBB https://www.soliforum.com/topic/2888/ceramic-head/ <![CDATA[Re: Ceramic head ?]]> Hi,

I found one on the ebay link above thank you. For me the benefit is only when you gum it, you can put the ceramic part in an oven at 500°C or more and gasify PTFE and ABS, you cannot with PEEK.
Ideally one without PTFE will be better but its difficult to polish a 2 mm inner bore at good price. Exact the hotend coming from Poland is a little bit bulky but well finished.

]]> https://www.soliforum.com/user/2190/ 2013-06-25T08:05:10Z https://www.soliforum.com/post/27835/#p27835 <![CDATA[Re: Ceramic head ?]]> The above link is where I purchased mine. I personally like it very much, as I had originally bought a hotend similar to the Therminator from some guy who built them in Poland. That style was much too bulky, with a lot of weight on the cylindrical heater block, and I could not get it to fit nicely without cutting a wider groove in the peek. This hotend is very small, lighter and shorter than the stock hotend or even J-heads, and prints nicely. It fits snug on Lawsy's MK-IV, which is also a big plus.

]]> https://www.soliforum.com/user/18/ 2013-06-25T02:24:30Z https://www.soliforum.com/post/27801/#p27801 <![CDATA[Re: Ceramic head ?]]> danny wrote:

I can see no benefit over peek.
fancy exotic material, but still has a teflon liner, so still can't go over 260 degrees, and will still irretrievably gum up of you accidentally try it.


also, can you remove the nozzle to unblock it? -it doesn't look like you can!

Have I missed a point somewhere?

The nozzle still threads in smile

At least the whole thing does not melt like peek so you only have to replace a liner smile

Other than the temp limit it looks like a nice hotend idea.

]]> https://www.soliforum.com/user/296/ 2013-06-24T16:55:37Z https://www.soliforum.com/post/27751/#p27751 <![CDATA[Re: Ceramic head ?]]> I can see no benefit over peek.
fancy exotic material, but still has a teflon liner, so still can't go over 260 degrees, and will still irretrievably gum up of you accidentally try it.


also, can you remove the nozzle to unblock it? -it doesn't look like you can!

Have I missed a point somewhere?

]]> https://www.soliforum.com/user/39/ 2013-06-24T16:17:43Z https://www.soliforum.com/post/27743/#p27743 <![CDATA[Re: Ceramic head ?]]> I found this on E-BAY

http://www.ebay.com/itm/Ceramic-Hotend- … 27d430a141

]]> https://www.soliforum.com/user/187/ 2013-06-24T07:51:46Z https://www.soliforum.com/post/27704/#p27704 <![CDATA[Re: Ceramic head ?]]> Hi Thank's a lot coleke.

]]> https://www.soliforum.com/user/2190/ 2013-06-24T07:37:13Z https://www.soliforum.com/post/27703/#p27703 <![CDATA[Re: Ceramic head ?]]> There is an article in hackaday, search for "ceramic extruder". The guy who made that piece is sellin them on eBay for somewhere around $50-60. That was found using the same keyword. I've installed one of these, it is working great.

]]> https://www.soliforum.com/user/18/ 2013-06-22T11:10:14Z https://www.soliforum.com/post/27516/#p27516 <![CDATA[Ceramic head ?]]> Hi everybody,

Have you more informations on ceramic's head like Zirconia, i saw that on the web but without more informations.

Sorry for my English smile I'm French

Regards

Gilles

]]> https://www.soliforum.com/user/2190/ 2013-06-20T12:37:36Z https://www.soliforum.com/post/27217/#p27217