<![CDATA[SoliForum - 3D Printing Community — Nice print with Laywoo-D3]]> 2013-08-05T07:50:53Z PunBB https://www.soliforum.com/topic/2868/nice-print-with-laywood3/ <![CDATA[Re: Nice print with Laywoo-D3]]> Its an external python script : http://www.thingiverse.com/thing:49276
Also available as a W3 Svc: http://www.tecrd.com/page/liens/stl_wood&lang=fr

]]> https://www.soliforum.com/user/663/ 2013-08-05T07:50:53Z https://www.soliforum.com/post/31939/#p31939 <![CDATA[Re: Nice print with Laywoo-D3]]> yeah i was just about to ask that and is it like a plugin for repetier?

]]> https://www.soliforum.com/user/2211/ 2013-08-04T23:47:08Z https://www.soliforum.com/post/31895/#p31895 <![CDATA[Re: Nice print with Laywoo-D3]]> Nice, what's the script you're using?

]]> https://www.soliforum.com/user/1702/ 2013-08-04T23:34:48Z https://www.soliforum.com/post/31892/#p31892 <![CDATA[Re: Nice print with Laywoo-D3]]> Thanks Rincewind for the information. I don't use any of those programs. Skeinforge just creates G codes which are sent to an Arduino controller. Unfortunately it's also not possible in skeinforge to change the nozzle diameter...

]]> https://www.soliforum.com/user/2784/ 2013-07-23T10:05:44Z https://www.soliforum.com/post/30690/#p30690 <![CDATA[Re: Nice print with Laywoo-D3]]> With skeinforge I don't know, as I am using Slic3r. Are you using RepetierHost or Pronterface? In Repetier it is very easy, there is a slider in the "manual" tab that allows you to change the flow during the print. I should also mention that I changed the nozzle diameter in the settings to .45 instead of .5. I found this in a forum somewhere and it apparently helps because the extruder pushes a bit less filament through the nozzle and it requires less force to extrude.

]]> https://www.soliforum.com/user/242/ 2013-07-23T08:40:04Z https://www.soliforum.com/post/30687/#p30687 <![CDATA[Re: Nice print with Laywoo-D3]]> I haven't tried the flow multiplier yet. I'm using skeinforge. Which setting is it exactly? I will post a picture later indeed smile. I'm now trying to increase flow rate. Thanks smile!

]]> https://www.soliforum.com/user/2784/ 2013-07-23T08:34:24Z https://www.soliforum.com/post/30686/#p30686 <![CDATA[Re: Nice print with Laywoo-D3]]> Ah ok smile

If you have gaps on the surface, the most obvious reason would be low flow rate... Have you tried increasing the flow multiplier? I think I have it close to 1 for Laywood

]]> https://www.soliforum.com/user/242/ 2013-07-23T07:00:36Z https://www.soliforum.com/post/30681/#p30681 <![CDATA[Re: Nice print with Laywoo-D3]]> He just signed up today and will need a few more posts before he can post a picture...

]]> https://www.soliforum.com/user/891/ 2013-07-23T06:16:14Z https://www.soliforum.com/post/30677/#p30677 <![CDATA[Re: Nice print with Laywoo-D3]]> Witte wrote:

That looks very nice! I have laywoo-3d here but I'm struggling with the settings... I'm using CubeX 0.5mm nozzle but what I get are products without a smooth surface. There are some little gaps at the surface of my products. Can you give some advice in good settings? Thanks.

Uhm... Can you post a picture?

]]> https://www.soliforum.com/user/242/ 2013-07-22T14:59:11Z https://www.soliforum.com/post/30593/#p30593 <![CDATA[Re: Nice print with Laywoo-D3]]> That looks very nice! I have laywoo-3d here but I'm struggling with the settings... I'm using CubeX 0.5mm nozzle but what I get are products without a smooth surface. There are some little gaps at the surface of my products. Can you give some advice in good settings? Thanks.

]]> https://www.soliforum.com/user/2784/ 2013-07-22T14:56:15Z https://www.soliforum.com/post/30592/#p30592 <![CDATA[Re: Nice print with Laywoo-D3]]> cyberpete wrote:

Looks really good. Might have to try that one. Only used ABS so faar.

You will enjoy it! Just make sure you use a 0.5mm nozzle as apparently a smaller one tends to clog. Also, be aware that it oozes quite a bit during travel, even with retraction, so preferably print one part at a time.

]]> https://www.soliforum.com/user/242/ 2013-06-27T07:35:01Z https://www.soliforum.com/post/28151/#p28151 <![CDATA[Re: Nice print with Laywoo-D3]]> Looks really good. Might have to try that one. Only used ABS so faar.

]]> https://www.soliforum.com/user/1528/ 2013-06-26T21:06:24Z https://www.soliforum.com/post/28112/#p28112 <![CDATA[Re: Nice print with Laywoo-D3]]> Yes, Very nice!

]]> https://www.soliforum.com/user/1277/ 2013-06-21T16:46:54Z https://www.soliforum.com/post/27383/#p27383 <![CDATA[Re: Nice print with Laywoo-D3]]> Staffordknot wrote:

Wow really good! How did you get the rings on the small gear to look offset?

Thank you for the nice responses!

The rings on the small gear are actually different layers. The top of the gear is not flat and it gets printed in multiple layers at different temperatures.

]]> https://www.soliforum.com/user/242/ 2013-06-20T08:18:38Z https://www.soliforum.com/post/27206/#p27206 <![CDATA[Re: Nice print with Laywoo-D3]]> Wow really good! How did you get the rings on the small gear to look offset?

]]> https://www.soliforum.com/user/1769/ 2013-06-20T08:10:20Z https://www.soliforum.com/post/27203/#p27203