<![CDATA[SoliForum - 3D Printing Community — Solidoodle Belt and Pulley specs / belt replacement guide]]> 2014-02-19T14:23:00Z PunBB https://www.soliforum.com/topic/2671/solidoodle-belt-and-pulley-specs-belt-replacement-guide/ <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Shipping is expensive, but worth it often. If you have a light enough order (<500g) and can afford the wait, you can request chinapost mail instead of fedex.

They're quiet and awkward to order from, but I've had both packages I order (a $40 order and a $120 order) arrive safely and relatively quickly.

]]> https://www.soliforum.com/user/192/ 2014-02-19T14:23:00Z https://www.soliforum.com/post/50200/#p50200 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Hazer wrote:
2n2r5 wrote:

I will hold off on my order then. It looks like it will be nearly $100 worth of hardware unless I start scouring ebay.

I have had good luck with the belts form here:
http://www.robotdigg.com/product

Might even have the right pulleys.

Those prices seem great! How's the shipping? I may have to look into a belt upgrade.

]]> https://www.soliforum.com/user/1682/ 2013-09-27T14:11:18Z https://www.soliforum.com/post/37462/#p37462 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> 2n2r5 wrote:

I will hold off on my order then. It looks like it will be nearly $100 worth of hardware unless I start scouring ebay.

I have had good luck with the belts form here:
http://www.robotdigg.com/product

Might even have the right pulleys.

]]> https://www.soliforum.com/user/2747/ 2013-09-25T16:17:26Z https://www.soliforum.com/post/37295/#p37295 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Cool! Thanks!

]]> https://www.soliforum.com/user/1682/ 2013-09-25T15:08:41Z https://www.soliforum.com/post/37291/#p37291 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Stevos758 wrote:
2n2r5 wrote:

http://2n2r5.com/pictures/printer/solidoodle.skp

in case you were wanting something for references and you don't have your machine. Here is that mock up

Not to bring up an old thread but IS this an accurate mockup of a sD3?

I just checked out your site for more info. Funny I just got back from Thailand!


It's an incomplete mockup but what I have there is accurate so far.

]]> https://www.soliforum.com/user/1906/ 2013-09-25T14:21:55Z https://www.soliforum.com/post/37285/#p37285 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> 2n2r5 wrote:

http://2n2r5.com/pictures/printer/solidoodle.skp

in case you were wanting something for references and you don't have your machine. Here is that mock up

Not to bring up an old thread but IS this an accurate mockup of a sD3?

I just checked out your site for more info. Funny I just got back from Thailand!

]]> https://www.soliforum.com/user/1682/ 2013-09-25T13:33:17Z https://www.soliforum.com/post/37281/#p37281 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> I will hold off on my order then. It looks like it will be nearly $100 worth of hardware unless I start scouring ebay.

]]> https://www.soliforum.com/user/1906/ 2013-06-17T03:11:09Z https://www.soliforum.com/post/26628/#p26628 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> So far my prints look exactly the same. Not sure if this mod is worth the effort and particularly the stuffing around with the rear 1/4 inch rod.

]]> https://www.soliforum.com/user/51/ 2013-06-17T03:08:45Z https://www.soliforum.com/post/26626/#p26626 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Here is the belt I am getting for that.
http://www.sdp-si.com/cd/PartDetail.asp … p;GROUP=TB

Pitch:    2mm (GT2)
Groove Number:    86
Material:    Neoprene
Belt Width:    6MM
Pitch Length:    172mm
Belt Type:    SINGLE SIDED
Tension Member(Cord):    FIBERGLASS

Pulley supplier is BBMAN
   
18-2P06-6FA2 x 5
Description:
18 Teeth
GT2
6mm Wide
.1875" bore

(needs to be widened from 4.76mm to 5mm)

18-2P06-6CA3
Description:
18 Teeth
GT2
6mm Wide
.250" bore

(will need to run grub screw all the way in or something to take up the .37mm gap)

]]> https://www.soliforum.com/user/1906/ 2013-06-17T02:02:13Z https://www.soliforum.com/post/26618/#p26618 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> 2n2r5 wrote:

Lawsy,

What size length did you get for your Y drive belt from the motor to the first shaft?

I didn't replace that little belt. As yet unable to find a local supplier...

]]> https://www.soliforum.com/user/51/ 2013-06-16T21:03:07Z https://www.soliforum.com/post/26581/#p26581 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> It's worse, the rod is 6mm which means the bushings have a 6mm bore, but the holes in the frame that the bushings are mounted in are 1/2".  Maybe you should get a 5mm rod, some 5x13mm flange bearings, and ground the holes out from 12.6mm to 13mm.

]]> https://www.soliforum.com/user/14/ 2013-06-16T17:27:50Z https://www.soliforum.com/post/26548/#p26548 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Lawsy,

What size length did you get for your Y drive belt from the motor to the first shaft?

]]> https://www.soliforum.com/user/1906/ 2013-06-16T17:14:26Z https://www.soliforum.com/post/26544/#p26544 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Everything is running fine using the original belts for the y-axis and the new belts for the x-axis.

3dcad, EEPROM instructions:

1. http://calculator.josefprusa.cz/

Get a ball park by entering the standard Solidoodle specs:

Motor step angle: 1.8
Driver microstepping: 1/16 uStep
Belt presets: MXL belts (2.03mm)
Belt pitch: 2.03mm
Pulley tooth count: 18

This will calculate to 87.58 steps per mm. Firmware is factory set to 88 steps per mm.

2. Change values in calculator to suit new belts and pulleys:

Motor step angle: 1.8
Driver microstepping: 1/16 uStep
Belt presets: GT2 belts (2.00mm)
Belt pitch: 2.00mm
Pulley tooth count: 20 (may be different for you depending on which pulleys you buy)

Calculates to 80 steps per mm. This is the value for the EEPROM settings.

3. Open Repetier-Host and connect.

Go to Config > Firmware EEPROM configuration

Change value from 88.00 to 80.00 for X and Y (depending on what belts you changed) on the top row.

Click Save to EEPROM and then yes.

Finished!

Print something round to see if it comes out as a circle or oval.

]]> https://www.soliforum.com/user/51/ 2013-06-15T04:48:17Z https://www.soliforum.com/post/26426/#p26426 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> http://2n2r5.com/pictures/printer/solidoodle.skp

in case you were wanting something for references and you don't have your machine. Here is that mock up

]]> https://www.soliforum.com/user/1906/ 2013-06-15T03:36:16Z https://www.soliforum.com/post/26419/#p26419 <![CDATA[Re: Solidoodle Belt and Pulley specs / belt replacement guide]]> Arrgh! Imperial strikes again.

I've drilled the holes but they are slightly off centre and there is no longer enough metal left for the grub screws to grab.

Unfortunately I'll have to change the y axis belts back to the MXL until I can sort out a replacement 5mm rod and bearings.

]]> https://www.soliforum.com/user/51/ 2013-06-14T23:49:09Z https://www.soliforum.com/post/26403/#p26403