SoliForum - 3D Printing Community — Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T13:40:30Z

Good to hear. Interesting that it was connecting at all

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T13:25:55Z

You guys can close this thread if you want. It appears the issue was that my com setting was 256000 instead of 250000. They should really put that in the initial documentation...

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T12:22:08Z

Hey Rincewind,
I have whatever the unit shipped with. I'll try your suggestion! Thank you!

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T12:21:30Z

I think it might be an out-of-memory error from the electronics. Do you have the stock firmware or Lawsy's? Try setting

#define BLOCK_BUFFER_SIZE 8

in Configuration_adv.h (you need to change it in two places) and reflash the firmware.

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T12:14:51Z

Repeated on other prints...but usually doesn't lock up on the other prints, and it will usually finish the job. However the pauses always cause an issue where it will tend to "grab" or leave a bit of plastic on the extruder. Having read the forums, I'm making sure my com settings are correct to see if that is possibly the issue, but any additional advice would be greatly useful!

Re: Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T12:13:46Z

One off or repeated on other prints?

Soliddoodle3 Finally Calibrated...locks up in middle of print job :(

2013-05-15T12:03:55Z

Hey Guys,
Finally got my solid doodle working. Finally got it printing a wonderfully calibrated print. Now onto the next problem. It just starts spewing out errors like mad.

07:57:47.890 : Error:No Checksum with line number, Last Line:5832
07:57:47.890 : Resend:5833
07:57:49.981 : Error:checksum mismatch, Last Line:5896
07:57:49.981 : Resend:5897
07:57:50.221 : Error:checksum mismatch, Last Line:5911
07:57:50.221 : Resend:5912
07:57:50.241 : Error:Line Number is not Last Line Number+1, Last Line:5911
07:57:50.241 : Resend:5912
07:57:51.773 : Error:checksum mismatch, Last Line:5965
07:57:51.773 : Resend:5966
07:57:54.743 : Error:checksum mismatch, Last Line:6066
07:57:54.743 : Resend:6067
07:57:57.313 : Printing layer 23 of 322
07:58:32.850 : Error:checksum mismatch, Last Line:6259
07:58:32.850 : Resend:6260
07:58:34.127 : Error:checksum mismatch, Last Line:6322
07:58:34.127 : Resend:6323
07:58:43.355 : Printing layer 24 of 322
07:59:21.447 : Error:checksum mismatch, Last Line:6984
07:59:21.447 : Resend:6985
07:59:24.448 : Error:checksum mismatch, Last Line:7112
07:59:24.448 : Resend:7113
07:59:25.693 : Error:checksum mismatch, Last Line:7165
07:59:25.693 : Resend:7166
07:59:25.885 : Error:checksum mismatch, Last Line:7173
07:59:25.885 : Resend:7174
07:59:25.905 : Error:Line Number is not Last Line Number+1, Last Line:7173
07:59:25.905 : Resend:7174

Then locks up, burns a huge hole through the model it was printing, and I have to disconnect/reconnect it to get it off the model. Really frustrating and depressing.

Any suggestions?