<![CDATA[SoliForum - 3D Printing Community — rostock delta G2S stepper motor woes]]> 2019-01-27T13:24:48Z PunBB https://www.soliforum.com/topic/17883/rostock-delta-g2s-stepper-motor-woes/ <![CDATA[Re: rostock delta G2S stepper motor woes]]>

watched the video and have successfully altered my stepper drivers. Still a few things to iron out but the steppers are moving smoothly now. thanks for all your help big_smile

Glad to be of service

While a ceramic screwdriver is not totally necessary IMHO a very  very good idea. It is the right tool for the job. and not that expensive. I would say anyone not haveing one in there tool kit should jet one. That is unless one has upgraded to firmware control of Vref.

]]> https://www.soliforum.com/user/6775/ 2019-01-27T13:24:48Z https://www.soliforum.com/post/148676/#p148676 <![CDATA[Re: rostock delta G2S stepper motor woes]]> watched the video and have successfully altered my stepper drivers. Still a few things to iron out but the steppers are moving smoothly now. thanks for all your help big_smile

]]> https://www.soliforum.com/user/20934/ 2019-01-27T13:05:58Z https://www.soliforum.com/post/148675/#p148675 <![CDATA[Re: rostock delta G2S stepper motor woes]]> I would actually say a ceramic screwdriver is necessary. If you slip even just on the stepper you could blow it out. Yes a stepper driver is only 5 to 10 bucks but a ceramic screwdriver is about the same cost on ebay or amazon and it will keep you from blowing one or more stepper drivers. Up to you in the long run but to me not worth the risk. Of course now I have an Azteeg X5 GT with Bigfoot stepper drivers so current is controlled through the firmware and no pots.

]]> https://www.soliforum.com/user/7731/ 2019-01-27T05:00:26Z https://www.soliforum.com/post/148670/#p148670 <![CDATA[Re: rostock delta G2S stepper motor woes]]> +1 to TinFalcon.  This was a daunting task when I first got my Solidoodle 3. I was afraid of doing something that could brick the system. Please follow the instructions in this video. (Ceramic screwdriver not necessary but just make sure you don't slip off the stepper driver controller).

I promise this is (as with most things in this forum) easy after you do it for the first time.

]]> https://www.soliforum.com/user/1906/ 2019-01-27T04:34:04Z https://www.soliforum.com/post/148669/#p148669 <![CDATA[Re: rostock delta G2S stepper motor woes]]> Thanks Tin Falcon

]]> https://www.soliforum.com/user/20934/ 2019-01-26T19:43:43Z https://www.soliforum.com/post/148662/#p148662 <![CDATA[Re: rostock delta G2S stepper motor woes]]> not difficult but there are some points to heed




http://rigidtalk.com/wiki/index.php?tit … Adjustment

]]> https://www.soliforum.com/user/6775/ 2019-01-25T23:16:09Z https://www.soliforum.com/post/148653/#p148653 <![CDATA[rostock delta G2S stepper motor woes]]> I have built and calibrated my G2S delta printer. this is my 2nd printer but my first one was already built so I have no experience in calibrating a printer from scratch.
it has a GT2560A board. My problem is the stepper motors keep skipping. I have checked the belts are tight enough but the skipping still continues. from what I can tell I need to adjust the current on the steppers but I have no experience in doing anything like this so I am a bit wary in just playing with the settings till it works in case I break something.
Can anyone give me a simple laymans guide to setting these as all the guides i have found get really technical and i get confused.
can someone help me please????

]]> https://www.soliforum.com/user/20934/ 2019-01-25T22:14:43Z https://www.soliforum.com/post/148649/#p148649