<![CDATA[SoliForum - 3D Printing Community — Simplify 3d question]]> 2018-09-16T15:08:55Z PunBB https://www.soliforum.com/topic/17598/simplify-3d-question/ <![CDATA[Re: Simplify 3d question]]> found it and got it straightened out
'Thanks
Dale

]]> https://www.soliforum.com/user/187/ 2018-09-16T15:08:55Z https://www.soliforum.com/post/146305/#p146305 <![CDATA[Re: Simplify 3d question]]> with a Makerbot printer the stock software is a POS so i am using Simplify 3D which so far has been better up until this point. the printer is closed source so their is not much i can do. (Not replacing board as long as it is working.)

]]> https://www.soliforum.com/user/187/ 2018-09-16T12:26:07Z https://www.soliforum.com/post/146302/#p146302 <![CDATA[Re: Simplify 3d question]]> I don't even know if mine is doing what I ask, so it is dependent on the software and what it has as its defaults.

I notice that the software tends to over ride what is asked of it in favour of defaults, IDK if that my particular frankenstein-i3 or marlin in general following orders from the driver software.

Try another interface, see if that helps.

]]> https://www.soliforum.com/user/18727/ 2018-09-16T11:43:38Z https://www.soliforum.com/post/146300/#p146300 <![CDATA[Re: Simplify 3d question]]> Yes but it still dies not print 241 after the first layer.
http://soliforum.com/i/?LOoQgHu.jpg

]]> https://www.soliforum.com/user/187/ 2018-09-16T10:57:41Z https://www.soliforum.com/post/146299/#p146299 <![CDATA[Re: Simplify 3d question]]> dubbsd wrote:

Carl here is my start G code
where do I put the 241° at.
for each extruder.

; **** Replicator 2X start.gcode ****
M73 P0 ; Enable build progress
G162 X Y F3000 ; Home XY maximum
G161 Z F1200 ; Home Z minimum
G92 Z-5 ; Set Z to -5
G1 Z0 ; Move Z to 0
G161 Z F100 ; Home Z slowly
M132 X Y Z A B ; Recall home offsets
M135 T0 ; Load right extruder offsets
G1 X-130 Y-75 Z30 F9000 ; Move to wait position off table
G130 X20 Y20 Z20 A20 B20 ; Lower stepper Vrefs while heating
M126 S[fan_speed_pwm] ; Set fan speed
M140 S[bed0_temperature] T0 ; Heat buildplate
M134 T0 ; Stabilize bed temperature
M104 S[extruder0_temperature] T0 ; Heat right extruder
M104 S[extruder1_temperature] T1 ; Heat left extruder
M133 T0 ; Stabilize right extruder temperature
M133 T1 ; Stabilize left extruder temperature
G130 X127 Y127 Z40 A127 B127 ; Default stepper Vrefs
G92 A0 B0 ; Zero extruders
G1 X100 Y-70 F9000 ; Move to front right corner of bed
G1 Z0.3 F6000 ; Move down to purge
G1 X-90 Y-70 E24 F2000 ; Extrude a line of filament across the front edge of the bed
G1 X-100 Y-70 F180 ; Wait for ooze
G1 X-110 Y-70 F5000 ; Fast wipe
G1 Z0.5 F100 ; Lift
G92 A0 B0 ; Zero extruders
M135 T1 ; Load left extruder offsets
G1 X-100 Y-65 F9000 ; Move to front left corner of bed
G1 Z0.3 F6000 ; Move down to purge
G1 X90 Y-65 E24 F2000 ; Extrude a line of filament across the front edge of the bed
G1 X100 Y-65 F180 ; Wait for ooze
G1 X110 Y-65 F5000 ; Fast wipe
G1 Z1 F100 ; Lift
G92 A0 B0 ; Zero extruders
M73 P1 ;@body (notify GPX body has started)
; **** end of start.gcode ****


Damn that is one hell of a start.. Mine only has like three maybe four lines.

The issue are these two lines..

M104 S[extruder0_temperature] T0 ; Heat right extruder
M104 S[extruder1_temperature] T1 ; Heat left extruder

Are these both set in this window?

http://soliforum.com/i/?tEohEo2.jpg

]]> https://www.soliforum.com/user/7731/ 2018-09-16T00:16:36Z https://www.soliforum.com/post/146296/#p146296 <![CDATA[Re: Simplify 3d question]]> Carl here is my start G code
where do I put the 241° at.
for each extruder.

; **** Replicator 2X start.gcode ****
M73 P0 ; Enable build progress
G162 X Y F3000 ; Home XY maximum
G161 Z F1200 ; Home Z minimum
G92 Z-5 ; Set Z to -5
G1 Z0 ; Move Z to 0
G161 Z F100 ; Home Z slowly
M132 X Y Z A B ; Recall home offsets
M135 T0 ; Load right extruder offsets
G1 X-130 Y-75 Z30 F9000 ; Move to wait position off table
G130 X20 Y20 Z20 A20 B20 ; Lower stepper Vrefs while heating
M126 S[fan_speed_pwm] ; Set fan speed
M140 S[bed0_temperature] T0 ; Heat buildplate
M134 T0 ; Stabilize bed temperature
M104 S[extruder0_temperature] T0 ; Heat right extruder
M104 S[extruder1_temperature] T1 ; Heat left extruder
M133 T0 ; Stabilize right extruder temperature
M133 T1 ; Stabilize left extruder temperature
G130 X127 Y127 Z40 A127 B127 ; Default stepper Vrefs
G92 A0 B0 ; Zero extruders
G1 X100 Y-70 F9000 ; Move to front right corner of bed
G1 Z0.3 F6000 ; Move down to purge
G1 X-90 Y-70 E24 F2000 ; Extrude a line of filament across the front edge of the bed
G1 X-100 Y-70 F180 ; Wait for ooze
G1 X-110 Y-70 F5000 ; Fast wipe
G1 Z0.5 F100 ; Lift
G92 A0 B0 ; Zero extruders
M135 T1 ; Load left extruder offsets
G1 X-100 Y-65 F9000 ; Move to front left corner of bed
G1 Z0.3 F6000 ; Move down to purge
G1 X90 Y-65 E24 F2000 ; Extrude a line of filament across the front edge of the bed
G1 X100 Y-65 F180 ; Wait for ooze
G1 X110 Y-65 F5000 ; Fast wipe
G1 Z1 F100 ; Lift
G92 A0 B0 ; Zero extruders
M73 P1 ;@body (notify GPX body has started)
; **** end of start.gcode ****

]]> https://www.soliforum.com/user/187/ 2018-09-15T21:48:25Z https://www.soliforum.com/post/146288/#p146288 <![CDATA[Re: Simplify 3d question]]> dubbsd wrote:

how to i set ABS to always print at 241° instead of 230°

Thanks
Dale


If you have your temp set for 241 in the extruder temp setting and it is the correct tool then there is a setting in your start gcode  that is changing it. What is your START gcode under the scripts tab?

]]> https://www.soliforum.com/user/7731/ 2018-09-15T20:31:54Z https://www.soliforum.com/post/146285/#p146285 <![CDATA[Simplify 3d question]]> how to i set ABS to always print at 241° instead of 230°

Thanks
Dale

]]> https://www.soliforum.com/user/187/ 2018-09-15T20:02:52Z https://www.soliforum.com/post/146284/#p146284