<![CDATA[SoliForum - 3D Printing Community — CR 10 printer question]]> 2018-03-02T13:36:00Z PunBB https://www.soliforum.com/topic/17132/cr-10-printer-question/ <![CDATA[Re: CR 10 printer question]]> You can get converted server supplies that are intended to power RC battery chargers but can be adapted to a 12 volt printer system easily. Most of those start at 900 watts and go up. That's 75 amps on a 12 volt system and should be enough for any size printer.

]]> https://www.soliforum.com/user/7731/ 2018-03-02T13:36:00Z https://www.soliforum.com/post/142792/#p142792 <![CDATA[Re: CR 10 printer question]]> Power supply have always been an issue for large printers.
go from an 8" x 8" or 200mm x 200mm bed to 300 x 300 and you double the area and therefore the power of the heater. so you need a PS that can drive it . the common workaround is going to a 24 volt system  but all components need to be able to handle this. Or you can run a heater off the mains and use a relay to control it.  The other alternative is a bigger cap 12 volt PS .

]]> https://www.soliforum.com/user/6775/ 2018-03-02T11:34:50Z https://www.soliforum.com/post/142788/#p142788 <![CDATA[Re: CR 10 printer question]]> Tin Falcon wrote:

they can be good printers . But there are several variants and they may come as a kit or preassembled.

Great thanks for the sharing smile

]]> https://www.soliforum.com/user/18526/ 2018-03-02T10:41:52Z https://www.soliforum.com/post/142785/#p142785 <![CDATA[Re: CR 10 printer question]]> I don't have CR-10. But I want that printer for a long time, so I read a lot about it. It is overall good printer and received lots of good comment. It is very easy to put together and can get your first print out with little fine tune. Large build volume.

ANET E10, CREALITY CR-10, and HICTOP CR-10 are basically same machine. There are also Tronxy X3S and TEVO Tornado with similar design.

The main concern is the heated bed heat up slow (15 minuts to 100C, 160W power supply may be the reason. max nozzle temperature is 230C).

2nd concern is single z-axis for 300 mm wide print bed.

3rd, check if it already include MOSFET upgrade to avoid main board burning issue.

The reason I have not decide to buy it because multiple complain about the noise. The main board have the pot to adjust motor current, but I think reduce motor current will increase the chance of layer shift given the heavy print bed.

]]> https://www.soliforum.com/user/17164/ 2018-02-13T22:23:34Z https://www.soliforum.com/post/142502/#p142502 <![CDATA[Re: CR 10 printer question]]> There are many reviews on you tube



https://www.youtube.com/results?search_ … lity+cr+10

]]> https://www.soliforum.com/user/6775/ 2018-02-13T00:35:33Z https://www.soliforum.com/post/142462/#p142462 <![CDATA[Re: CR 10 printer question]]> Or possibly Anet cloned the Crealty  ??

]]> https://www.soliforum.com/user/6775/ 2018-02-13T00:30:44Z https://www.soliforum.com/post/142461/#p142461 <![CDATA[Re: CR 10 printer question]]> When Googled you get hits for the Anet so they are just Anet clones as far as I can tell.

]]> https://www.soliforum.com/user/7731/ 2018-02-13T00:09:06Z https://www.soliforum.com/post/142458/#p142458 <![CDATA[Re: CR 10 printer question]]> they can be good printers . But there are several variants and they may come as a kit or preassembled.


https://printedsolid.com/collections/3d … ucts/cr10s

]]> https://www.soliforum.com/user/6775/ 2018-02-13T00:08:03Z https://www.soliforum.com/post/142457/#p142457 <![CDATA[CR 10 printer question]]> is the CR 10 a good printer or does it fall in the same catagory as an XYZ printer.
A friend of mine has one coming and wants me to set it up.

Thanks
Dale

]]> https://www.soliforum.com/user/187/ 2018-02-12T22:36:31Z https://www.soliforum.com/post/142453/#p142453