<![CDATA[SoliForum - 3D Printing Community — Davinci 1.0A power supply outputs]]> 2018-02-01T01:18:42Z PunBB https://www.soliforum.com/topic/17091/davinci-10a-power-supply-outputs/ <![CDATA[Re: Davinci 1.0A power supply outputs]]> On a side note- I have found the pinouts for the steppers, but am unsure of the orientation of those diagrams. Shaft towards you, or away?

]]> https://www.soliforum.com/user/18299/ 2018-02-01T01:18:42Z https://www.soliforum.com/post/142084/#p142084 <![CDATA[Re: Davinci 1.0A power supply outputs]]> carl_m1968 wrote:
ironjoe13 wrote:

Thanks Carl!

I assume I connect all 12V and all GND to the one inlet...?

3 yellows (I assume 12V)
3 black ( assumed GND)
and the rest are unused


That is correct. Just tape the others up to avoid them shorting on anything. The only issue is you may need to upgrade the supply to a higher wattage one as the RAMPS seems to need more current to heat the bed. Keep in mind the RAMPS has two power inputs. One for it's power and one for bed heater power. You will need to make jumpers to bring the power from the main power side over to the bed power side as well.

Hmmm... I think I will try to keep the original wiring divisions and see how it fairs.
2 Yellow, 2 Black to bed heater (original clear 4way plug)
1 Yellow, 1 Black to board

]]> https://www.soliforum.com/user/18299/ 2018-01-31T16:47:04Z https://www.soliforum.com/post/142073/#p142073 <![CDATA[Re: Davinci 1.0A power supply outputs]]> ironjoe13 wrote:

Thanks Carl!

I assume I connect all 12V and all GND to the one inlet...?

3 yellows (I assume 12V)
3 black ( assumed GND)
and the rest are unused


That is correct. Just tape the others up to avoid them shorting on anything. The only issue is you may need to upgrade the supply to a higher wattage one as the RAMPS seems to need more current to heat the bed. Keep in mind the RAMPS has two power inputs. One for it's power and one for bed heater power. You will need to make jumpers to bring the power from the main power side over to the bed power side as well.

]]> https://www.soliforum.com/user/7731/ 2018-01-31T16:12:20Z https://www.soliforum.com/post/142072/#p142072 <![CDATA[Re: Davinci 1.0A power supply outputs]]> Thanks Carl!

I assume I connect all 12V and all GND to the one inlet...?

3 yellows (I assume 12V)
3 black ( assumed GND)
and the rest are unused

]]> https://www.soliforum.com/user/18299/ 2018-01-31T16:07:29Z https://www.soliforum.com/post/142071/#p142071 <![CDATA[Re: Davinci 1.0A power supply outputs]]> If you are going to RAMPS all you will need is 12 volts. I did not use stock lighting when I swapped mine, I used LED strips which ran on 12 volts and mounted on both sides for better lighting. I believe the stock lights run on 5 volts.

]]> https://www.soliforum.com/user/7731/ 2018-01-31T15:53:41Z https://www.soliforum.com/post/142070/#p142070 <![CDATA[Davinci 1.0A power supply outputs]]> Currently starting the conversion over to RAMPS 1.4 by virtue of MKS GEN V1.4 board.

My question is- what power outputs are needed?

I no longer need the opto endstops (TMC2130 drivers) so I assume I do not need the 3.3V or 5V (unless for lighting or fans)?

The Power supply states:
+3.3V @ 12A
+5V   @ 14A
+12V  @ 15A
-12V  @0.3A
+5Vsb @2.0A

Mostly stock mechanicals, E3DV6 and additional cooing fan.

Any help is much appreciated, thanks.

]]> https://www.soliforum.com/user/18299/ 2018-01-31T15:43:50Z https://www.soliforum.com/post/142069/#p142069