<![CDATA[SoliForum - 3D Printing Community — Wiring the MK2a to direct 12V PowerSupply ??]]> 2017-12-20T19:11:31Z PunBB https://www.soliforum.com/topic/16970/wiring-the-mk2a-to-direct-12v-powersupply/ <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> You could wire it just about the same as the filastruder instructions. Just without the motor and stall protection board. heat bed in place of heat band

]]> https://www.soliforum.com/user/6797/ 2017-12-20T19:11:31Z https://www.soliforum.com/post/140883/#p140883 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> Hi Tim,

- Like you suggested, I guess the SESTOS D1S-2R-24 should be a good option, over the board I suggested.

- Could you help me with, what the connection diagram would look like? Below are the components I have/intend to buy:
1.  Power Supply 12Vdc
https://www.ebay.com/itm/SUPERNIGHT-12V … 4adebca1da
2.  HeatBed
https://www.ebay.com/i/171996091360?rt=nc
3.  Thermister

Would I need anything else other than wires, to make this run independently?

]]> https://www.soliforum.com/user/17567/ 2017-12-20T18:27:52Z https://www.soliforum.com/post/140880/#p140880 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> Looks like it would work . You may need an additional SSR to power the heat bed. Cheap enough assuming you do not need this for critical control and you are not in a rush.
What is your application if I may ask.

]]> https://www.soliforum.com/user/6775/ 2017-12-20T00:22:23Z https://www.soliforum.com/post/140848/#p140848 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> Hi there,

- Sorry, I did not notice I did not notice I posted it in the Filastruder Board.

- Would something like the below board work?
https://www.ebay.com/itm/Temperature-Co … 1918997931

]]> https://www.soliforum.com/user/17567/ 2017-12-19T19:12:46Z https://www.soliforum.com/post/140827/#p140827 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> the pid controler from filasruder would be a good option

]]> https://www.soliforum.com/user/6775/ 2017-12-19T11:28:44Z https://www.soliforum.com/post/140811/#p140811 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> The simplest would probably just jet a ramps bard w/ arduino 2560  and a thermisistor. . Maybe a 2o04 controller board . or just find a good arduino book like the Arduino cook book  it should give I/O info for such a projects.

]]> https://www.soliforum.com/user/6775/ 2017-12-19T11:27:22Z https://www.soliforum.com/post/140810/#p140810 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> heated bed on a filastruder?

]]> https://www.soliforum.com/user/6797/ 2017-12-19T11:18:28Z https://www.soliforum.com/post/140809/#p140809 <![CDATA[Wiring the MK2a to direct 12V PowerSupply ??]]> Hey there,

I'm a newbie, trying to figure out if there is a way to wire the MK2a Heatbed directly to a 12V Power Supply. I mean, independent from the 3D Printers control board. What would be the components I need and the wiring/ connections to make?

12V ---------> ??????? ----------> Mk2a /HeatBed

]]> https://www.soliforum.com/user/17567/ 2017-12-19T07:24:27Z https://www.soliforum.com/post/140807/#p140807