<![CDATA[SoliForum - 3D Printing Community — filastruder only works in reverse GF45 - v2.0]]> 2017-11-01T15:05:39Z PunBB https://www.soliforum.com/topic/16863/filastruder-only-works-in-reverse-gf45-v20/ <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> It looks like the motor has been overloaded, and the stall protection board may not have been set up properly. All motors are tested before shipment.

In the assembly process, there is a step that asks the user to confirm the auger rotates freely by hand. Did it rotate freely then?

Did you add any plastic yet? Hold off on that until the auger is spinning freely.

How did you configure the limit on the stall protection board?

Replacement gears are here:

https://www.filastruder.com/collections … ment-gears

]]> https://www.soliforum.com/user/221/ 2017-11-01T15:05:39Z https://www.soliforum.com/post/139383/#p139383 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> http://soliforum.com/i/?226PIy9.jpg

This one has small damage hard to pick up on camera this is  gear 3

]]> https://www.soliforum.com/user/17751/ 2017-10-31T14:10:36Z https://www.soliforum.com/post/139351/#p139351 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> http://soliforum.com/i/?klrWMnL.jpg

]]> https://www.soliforum.com/user/17751/ 2017-10-31T14:00:35Z https://www.soliforum.com/post/139350/#p139350 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]>

I disconnected everything and only used power supply to the mortar still sounds like skipping gears ?

]]> https://www.soliforum.com/user/17751/ 2017-10-31T13:42:40Z https://www.soliforum.com/post/139348/#p139348 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> A grinding sound indicates that one or more gears are stripped in the gearbox. Would recommend checking the gears. If stripped, we do well replacements. You'll also want to check the stall protection board current limit, as that prevents the gearbox from damaging itself.

In the assembly process, there is a step that asks the user to confirm the auger rotates freely by hand. Did it rotate freely yet?

Did you add any plastic yet? Hold off on that until the auger is spinning freely.

]]> https://www.soliforum.com/user/221/ 2017-10-31T13:29:03Z https://www.soliforum.com/post/139345/#p139345 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> you should go through the wiring and make sure its all connected correctly

]]> https://www.soliforum.com/user/6797/ 2017-10-31T10:25:33Z https://www.soliforum.com/post/139341/#p139341 <![CDATA[filastruder only works in reverse GF45 - v2.0]]> my new filastruder v2.0  only works in reverse if I change the motor cables it just makes a grinding sound doesn't move

5 hours can't work this out sad
things I tried looson the screws
change Stall Protection

thanks

]]> https://www.soliforum.com/user/17751/ 2017-10-30T23:37:16Z https://www.soliforum.com/post/139328/#p139328