<![CDATA[SoliForum - 3D Printing Community — Davinci Mini 3D printer Repetier firmware?]]> 2018-09-20T13:30:50Z PunBB https://www.soliforum.com/topic/16351/davinci-mini-3d-printer-repetier-firmware/ <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> chotucakel wrote:

I have also bought a mid-range affordable 3d-printer and I am quite satisfied with the experience. Its service center assistance is good and the online support https://supportnumbers.net/hp-support-assistant/ is very responsive.

more spam

]]> https://www.soliforum.com/user/6797/ 2018-09-20T13:30:50Z https://www.soliforum.com/post/146409/#p146409 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> I have also bought a mid-range affordable 3d-printer and I am quite satisfied with the experience. Its service center assistance is good and the online support https://supportnumbers.net/hp-support-assistant/ is very responsive.

]]> https://www.soliforum.com/user/19876/ 2018-09-19T21:38:51Z https://www.soliforum.com/post/146398/#p146398 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> Entwere wrote:

davinci printers are good

Do you or have you actually owned one? I have and I can say that the 1.0 is junk in stock form.

]]> https://www.soliforum.com/user/7731/ 2017-05-08T11:16:22Z https://www.soliforum.com/post/135278/#p135278 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> davinci printers are good

]]> https://www.soliforum.com/user/16775/ 2017-05-08T10:50:27Z https://www.soliforum.com/post/135277/#p135277 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> carl_m1968 wrote:

Most are using RAMPS 1.4 and one of it's associated LCD's. You would also need endstops as the stock one would require installing in line pullup and limiting resistors.

Ok thank you very much. Ill look into this.

]]> https://www.soliforum.com/user/16685/ 2017-04-17T17:49:20Z https://www.soliforum.com/post/134664/#p134664 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> dejecj wrote:
carl_m1968 wrote:

it is not compatible with mini or the Jr. right now. It may never be based on limited owners of these models. What most do is gut them and add a different open source controller and display.

Thanks for the quick reply. I am not yet familiar with open source alternatives. Do you know any of the top of your head that you could recommend?

Most are using RAMPS 1.4 and one of it's associated LCD's. You would also need endstops as the stock one would require installing in line pullup and limiting resistors.

]]> https://www.soliforum.com/user/7731/ 2017-04-17T17:45:09Z https://www.soliforum.com/post/134663/#p134663 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> carl_m1968 wrote:

it is not compatible with mini or the Jr. right now. It may never be based on limited owners of these models. What most do is gut them and add a different open source controller and display.

Thanks for the quick reply. I am not yet familiar with open source alternatives. Do you know any of the top of your head that you could recommend?

]]> https://www.soliforum.com/user/16685/ 2017-04-17T17:05:56Z https://www.soliforum.com/post/134661/#p134661 <![CDATA[Re: Davinci Mini 3D printer Repetier firmware?]]> dejecj wrote:

Hello guys, first time poster and new to the 3d printing scene. I have just bought a daVinci Mini 3d printer as my first 3d printer. It was affordable and I read it's a good starter printer. However, I am not too exited about being tied down to their filament. I've seen plenty of videos for flashing the v1 to repetier but absolutely nothing on the other models including the mini. So my question is, has anybody flashed their mini to repetier or is it even compatible? A little direction on how to go about it would be greatly appreciated.

Thanks.

it is not compatible with mini or the Jr. right now. It may never be based on limited owners of these models. What most do is gut them and add a different open source controller and display.

]]> https://www.soliforum.com/user/7731/ 2017-04-17T16:55:35Z https://www.soliforum.com/post/134660/#p134660 <![CDATA[Davinci Mini 3D printer Repetier firmware?]]> Hello guys, first time poster and new to the 3d printing scene. I have just bought a daVinci Mini 3d printer as my first 3d printer. It was affordable and I read it's a good starter printer. However, I am not too exited about being tied down to their filament. I've seen plenty of videos for flashing the v1 to repetier but absolutely nothing on the other models including the mini. So my question is, has anybody flashed their mini to repetier or is it even compatible? A little direction on how to go about it would be greatly appreciated.

Thanks.

]]> https://www.soliforum.com/user/16685/ 2017-04-17T16:42:54Z https://www.soliforum.com/post/134659/#p134659