<![CDATA[SoliForum - 3D Printing Community — Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> 2021-03-24T22:04:50Z PunBB https://www.soliforum.com/topic/16192/davinci-10-e3d-v6-easy-direct-fit-direct-drive/ <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> https://www.thingiverse.com/thing:2144035

]]> https://www.soliforum.com/user/9111/ 2021-03-24T22:04:50Z https://www.soliforum.com/post/154618/#p154618 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> Does anyone have the models for this? I can't download the lock piece and the fan mounts. I managed to recreate the lock piece but I can't recreate the fan mount.

]]> https://www.soliforum.com/user/25798/ 2021-03-24T15:04:20Z https://www.soliforum.com/post/154617/#p154617 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> I would also like to update my Davinci 1.0 AIO.  Got mines secondhand and would love to be able to print in PETG.

]]> https://www.soliforum.com/user/9111/ 2021-03-14T02:00:27Z https://www.soliforum.com/post/154600/#p154600 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> Hello!

Is this design still out there?? Ii probably the best E3D v6 Mod that I have seen, I will love to give it a try!!

]]> https://www.soliforum.com/user/25760/ 2021-03-11T19:03:40Z https://www.soliforum.com/post/154596/#p154596 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> Update:

I have made the layer cooler smaller some people were concerned with collisions. Also, if the fan setting is not changed in configuration.h to re-purpose you might get thermistor decouple errors.

#define REPURPOSE_FAN_TO_COOL_EXTRUSIONS 1 //Setting this to 1 will repurpose the main Extruder cooling fan to be controlled VIA M106/M107
]]> https://www.soliforum.com/user/16347/ 2017-03-05T19:10:19Z https://www.soliforum.com/post/133393/#p133393 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> The next task at hand is to find what pin on the processor controls the second extruder. If I populate the mosfet that controls the heater cartridge for extruder 2, I can get the fan to switch on and off.

]]> https://www.soliforum.com/user/16347/ 2017-03-03T13:14:36Z https://www.soliforum.com/post/133290/#p133290 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> willthiswork89 wrote:

i just realize dyou are running a bowden setup this does not work with the direct drive da vinci 1.0 like i have sad

This is NOT a Bowden. This uses the stock motor and tensioner. I guess the pictures do not show the motor but I promise that it is there. If I went Bowden, I would not have sacrificed the extra 23.6mm.

R29 is 10K which is open on most other control boards. You don't have to do this but I wanted to use Table 8 in firmware which was made for the E3D thermsitor.

See this thread about removing R29
https://forum.voltivo.com/showthread.php?tid=8308

Part of this process I updated the firmware to Repetier 0.92.10 by LUC so I figured that I might as well use the correct thermistor table. I verified it with a thermocouple and its pretty dead on.

]]> https://www.soliforum.com/user/16347/ 2017-03-03T04:07:59Z https://www.soliforum.com/post/133284/#p133284 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> i just realize dyou are running a bowden setup this does not work with the direct drive da vinci 1.0 like i have sad

]]> https://www.soliforum.com/user/15686/ 2017-03-03T02:06:22Z https://www.soliforum.com/post/133283/#p133283 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> how or where did you read that you need to snap out r29? im looking all over for that documentation

]]> https://www.soliforum.com/user/15686/ 2017-03-03T02:01:18Z https://www.soliforum.com/post/133282/#p133282 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> UPDATE:

Prints NinjaFlex like a dream at 1600mm/min @ 265C

More pictures as requested:
http://soliforum.com/i/?IP2S3Km.jpg
http://soliforum.com/i/?sQMS4hn.jpg

Removed R29 so that table 8 in firmware can be used for the thermistor.
http://soliforum.com/i/?b2k2jf7.jpg

Bridged the mosfet pads  for the second extruder which the 1.0 doesn't have and installed a header for the E3D fan. The stock fan can be used for layer cooling now.
http://soliforum.com/i/?f6mUmgk.jpg

]]> https://www.soliforum.com/user/16347/ 2017-03-02T19:32:12Z https://www.soliforum.com/post/133262/#p133262 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> willthiswork89 wrote:

the fan shroud is required? i ran 12v for the e3d already. Some more pics of the setup inside would be awesome. I'm a bit confused by the fan duct vs layer cooling duct.

Im super excited this is exactly what i was looking for i kept thinking "man why is this so involved just to put a different hot end on " so thank you very much


I guess I should have listed my print settings.

Print Orientations:

http://soliforum.com/i/?qsRg6hk.jpg
My Settings
http://soliforum.com/i/?ekP4UKi.jpg
http://soliforum.com/i/?PHwle43.jpg
http://soliforum.com/i/?Ho66DBa.jpg

MAKE SURE WHEN YOU ARE DONE THAT YOU UPDATE YOUR Z OFFSET IN EEPROM (I used Repetier Host and my offset from Z home to the tip of the new hot end is 23.6mm).

Manually Level the bed AFTER setting the z offset and crank the screws down a couple turns to be safe.


I CANNOT STRESS THIS ENOUGH. DO NOT USE THE BED LEVELING FROM THE PRINTER MENU. IT WILL CRASH INTO THE BED.

I am looking into modifying the firmware to move z first when bed leveling. Manual Leveling in S3D works just fine but start with slow speeds and be prepared to kill the power if it is going to crash.

]]> https://www.soliforum.com/user/16347/ 2017-03-02T17:00:19Z https://www.soliforum.com/post/133261/#p133261 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> Great work. I think I am going to try this one.

]]> https://www.soliforum.com/user/12136/ 2017-03-02T13:36:55Z https://www.soliforum.com/post/133259/#p133259 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> ok nvm now that its printed it makes a whole lot more sense but i do have a question about the horizontal movement im having... have you found a way to eliminate that? seems like that wiggle could cause some issues  during print

]]> https://www.soliforum.com/user/15686/ 2017-03-02T02:40:19Z https://www.soliforum.com/post/133249/#p133249 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> the fan shroud is required? i ran 12v for the e3d already. Some more pics of the setup inside would be awesome. I'm a bit confused by the fan duct vs layer cooling duct.

Im super excited this is exactly what i was looking for i kept thinking "man why is this so involved just to put a different hot end on " so thank you very much

]]> https://www.soliforum.com/user/15686/ 2017-03-02T01:48:26Z https://www.soliforum.com/post/133248/#p133248 <![CDATA[Re: Davinci 1.0 E3D V6 Easy Direct Fit Direct Drive]]> The locking piece is what holds the E3D in place. It allows rotation but still holds it securely.

Special Note:

The lower fan duct should be installed with the unit not clipped in place and before the heater cartridge is clamped in. The duct has a little cutout that aligns with part of the carriage. The fit is tight but when you have the parts it will make more sense.

]]> https://www.soliforum.com/user/16347/ 2017-03-01T14:46:54Z https://www.soliforum.com/post/133226/#p133226