<![CDATA[SoliForum - 3D Printing Community — Prusa i3 keeps switching off!]]> 2016-10-01T00:22:28Z PunBB https://www.soliforum.com/topic/15385/prusa-i3-keeps-switching-off/ <![CDATA[Re: Prusa i3 keeps switching off!]]>

You could put a multimeter on the powersupply and monitor the volatages and see if it sags, or drops out.

if you are looking for constant monitoring small digital volt meters are available. but as pointed out by the OP the real problem was a loose connection the ramps board.. This is common with screw terminals in electronics. there are several ways to deal with this.
some manufacturers will add a crimp on connector that will not crush. the wires can be tinned. instrument grade lock tight may work.  .
Good grade connectors can help. As will scheduled preventative maintenance checks.
Tin

]]> https://www.soliforum.com/user/6775/ 2016-10-01T00:22:28Z https://www.soliforum.com/post/127279/#p127279 <![CDATA[Re: Prusa i3 keeps switching off!]]> I've had the same problem. I used these to replace the original ones
10Pcs 300V 15A 5.08mm Pitch 4-Pin PCB Screw Terminal Block Connector https://www.amazon.com/dp/B00QC6QS5W/re … 7xbA0QN5H1

]]> https://www.soliforum.com/user/6797/ 2016-09-30T10:48:55Z https://www.soliforum.com/post/127265/#p127265 <![CDATA[Re: Prusa i3 keeps switching off!]]> You could put a multimeter on the powersupply and monitor the volatages and see if it sags, or drops out.
https://descargartonos.info/notificacio … a-mensajes

]]> https://www.soliforum.com/user/14942/ 2016-09-30T08:59:52Z https://www.soliforum.com/post/127263/#p127263 <![CDATA[Re: Prusa i3 keeps switching off!]]> Yeah thanks guys I think it was caused by a loose connection. Scary thing could have burnt my house down! I will definately make sure I check over everything everytime.

]]> https://www.soliforum.com/user/14748/ 2016-08-24T10:25:15Z https://www.soliforum.com/post/126495/#p126495 <![CDATA[Re: Prusa i3 keeps switching off!]]> it seems the power terminals on Ramps boards frequently have this issue.

It is wise to periodically check and tighten as needed all screw terminal connections - they can, and do, loosen up with multiple on/off cycles (heat and cool)

]]> https://www.soliforum.com/user/10399/ 2016-08-24T01:34:51Z https://www.soliforum.com/post/126490/#p126490 <![CDATA[Re: Prusa i3 keeps switching off!]]> something caused it to melt. could be loose connection and arcing or could be a short. Be fore moving forward check your hot end and heat bed resistance.
you should read a few  ohms but not zero .
tin

]]> https://www.soliforum.com/user/6775/ 2016-08-23T22:57:21Z https://www.soliforum.com/post/126488/#p126488 <![CDATA[Re: Prusa i3 keeps switching off!]]> Turns out the terminal block to power the board has melted! So I need a new terminal block what Amp rating block do I need to buy?

]]> https://www.soliforum.com/user/14748/ 2016-08-23T15:45:09Z https://www.soliforum.com/post/126480/#p126480 <![CDATA[Re: Prusa i3 keeps switching off!]]> I found the problem. It was a loose connection smh lol. Thanks for your help.

]]> https://www.soliforum.com/user/14748/ 2016-08-23T12:24:22Z https://www.soliforum.com/post/126478/#p126478 <![CDATA[Re: Prusa i3 keeps switching off!]]> is it switching power off completely?
Or is is disconnecting from PC? (if you are connected to PC that is)
If you are connected to a PC and it is disconnecting from that, try a different USB cable 1st.

If it is losing power completely - 1st, make sure your connections are good and tight at the power supply and at the board.
it does sound like a possible board issue if you have replaced the power supply & all connections are good.

Personally, I refuse to buy anything from Aliexpress - I dont care how cheap the prices are - you get what you pay for.

]]> https://www.soliforum.com/user/10399/ 2016-08-23T11:45:15Z https://www.soliforum.com/post/126477/#p126477 <![CDATA[Re: Prusa i3 keeps switching off!]]> Hey guys just received my new 12v power supply rated 30A 360W. I installed it to my printer and I am still getting the same problem with it turning off. Could it possibly be something to do with the mainboard?

Now my printer is switching off when I turn both heatbed and extruder on its not even getting up to temperature.

]]> https://www.soliforum.com/user/14748/ 2016-08-23T10:59:20Z https://www.soliforum.com/post/126476/#p126476 <![CDATA[Re: Prusa i3 keeps switching off!]]> Yeah it's 12v thanks for your help!

]]> https://www.soliforum.com/user/14748/ 2016-08-16T20:06:33Z https://www.soliforum.com/post/126302/#p126302 <![CDATA[Re: Prusa i3 keeps switching off!]]> verify the voltage output on your current power supply (should say on it somewhere) but I am thinking it should be 12v

]]> https://www.soliforum.com/user/10399/ 2016-08-16T19:37:44Z https://www.soliforum.com/post/126301/#p126301 <![CDATA[Re: Prusa i3 keeps switching off!]]> Thanks guys I will buy one of these and let you know how it goes. Hopefully it works!
Is it the 12v or 24v I need to get?

]]> https://www.soliforum.com/user/14748/ 2016-08-16T19:24:53Z https://www.soliforum.com/post/126300/#p126300 <![CDATA[Re: Prusa i3 keeps switching off!]]> Sounds like a failing power supply to me, too...

I can highly recommend this one: http://www.printitindustries.com/collec … wer-supply

]]> https://www.soliforum.com/user/10399/ 2016-08-16T19:12:50Z https://www.soliforum.com/post/126299/#p126299 <![CDATA[Re: Prusa i3 keeps switching off!]]> Buy a better power supply
The super night is a popular tested choice and will run you about $29 you want one rated for at least IIRC 360 watts.

]]> https://www.soliforum.com/user/6775/ 2016-08-16T18:33:27Z https://www.soliforum.com/post/126294/#p126294