<![CDATA[SoliForum - 3D Printing Community — deformation test]]> 2017-04-28T04:58:34Z PunBB https://www.soliforum.com/topic/15235/deformation-test/ <![CDATA[Re: deformation test]]> Thanks guys.
You cured me of my phobia for change settings i don't know of in software tongue
I think i will try to use Pirvan's guide to align multi angle scans, for my building,
to "lighten" up some blind spot areas.
I will return when finished, with pictures.

Great guides, by the way, without them i would never get any usefully out of the scanner i'm sure wink

]]> https://www.soliforum.com/user/16713/ 2017-04-28T04:58:34Z https://www.soliforum.com/post/134998/#p134998 <![CDATA[Re: deformation test]]> Awesome!  I'm happy to see you up and running.

- Uriah

]]> https://www.soliforum.com/user/4789/ 2017-04-27T23:59:33Z https://www.soliforum.com/post/134991/#p134991 <![CDATA[Re: deformation test]]> Good job!  You will enjoy your Atlas3D very much.

I have played with the settings of Noise Removal, Image Threshold Mode and Laser Threshold, which has helped with noise and geometry detection.

]]> https://www.soliforum.com/user/4251/ 2017-04-27T19:54:22Z https://www.soliforum.com/post/134982/#p134982 <![CDATA[Re: deformation test]]> Reversed lasers....  Know we all know when we see that kind of deformation.

Nice job with the scans.

]]> https://www.soliforum.com/user/1357/ 2017-04-27T13:39:41Z https://www.soliforum.com/post/134973/#p134973 <![CDATA[Re: deformation test]]> Here the cat earlier, now its down from its hilltop:
There is still alot of "errors" in it, just removed the worst noise, but now i will start to find optimal
light/settings to get the best result.
But its better than i hoped for big_smile

http://soliforum.com/i/?pBvmwJi.png

]]> https://www.soliforum.com/user/16713/ 2017-04-27T13:30:55Z https://www.soliforum.com/post/134972/#p134972 <![CDATA[Re: deformation test]]> New update...
I dismantled my Atlas 3D completely, and when i assembled it again, i was wondering where left/right laser had to be.
Was it left as seen from turntable or from camera....
First time i thought it had to be seen from turntable...
Now i know its seen from camera... Oh well.... Shame on me. (To my defense, English isn't my mother language)
Here is two screenshot from last scan. I just can't get my arms down big_smile big_smile
I know there is still alot of work to do, like remove noise, change settings etc. BUT big_smile IT WORKS perfect !!!!!
Btw. Those new babies i just bought, they wasn't that much improvement imo. The default pair, worked just as good.
Well here is screenshot, and there is no hill below big_smile
http://soliforum.com/i/?Z4TNxzT.png
http://soliforum.com/i/?AKTOvJj.png

]]> https://www.soliforum.com/user/16713/ 2017-04-27T10:38:10Z https://www.soliforum.com/post/134970/#p134970 <![CDATA[Re: deformation test]]> Guffer wrote:

It is the acrylic kit.

(I sincerely don't hope i happen to highjack someone elses thread, then pls say so, and i will
make a new thread, with my scanner problem:) )

I think your problem seems relevant to the original subject, no worries.  It turned out to be dimension settings for them too.  Once you get your Atlas3D up and running, you'll be pleased with what it can do!  There's lots of good info for it in these forums.

]]> https://www.soliforum.com/user/4251/ 2017-04-26T20:30:05Z https://www.soliforum.com/post/134964/#p134964 <![CDATA[Re: deformation test]]> The problem may be your light source. If you are scanning with your lighting set up the same as in your preview then the scanner is seeing that shadow at the base of the bottle as a curve you need equal lighting from both sides or straight from the cameras view. Shadows will cause all kinds of issues with scanning.

There also seems to be a light source above and behind the scanning area as well. Looks to me like the focus on your camera is too far back and it sees too much of the area around the object.

From what I found with my scanner the focus of the camera should only see from edge to edge of the turn table. That also limits height to the same width as the turn table.

]]> https://www.soliforum.com/user/7731/ 2017-04-26T19:48:38Z https://www.soliforum.com/post/134959/#p134959 <![CDATA[Re: deformation test]]> It is the acrylic kit.

I have dismantled the scanner completely, since i had to change the lasers to my new babies.
And the turn plate, need a firm hand to make sure it wasn't that to make the troubles tongue
I will return when all is assembled, and finished first scan.

(I sincerely don't hope i happen to highjack someone elses thread, then pls say so, and i will
make a new thread, with my scanner problem:) )

]]> https://www.soliforum.com/user/16713/ 2017-04-26T18:28:25Z https://www.soliforum.com/post/134958/#p134958 <![CDATA[Re: deformation test]]> Is this an acrylic frame?

If so, stop measuring.  Set the parameters to the numbers indicated in previous posts.

]]> https://www.soliforum.com/user/4251/ 2017-04-26T11:24:49Z https://www.soliforum.com/post/134953/#p134953 <![CDATA[Re: deformation test]]> The building i tried earlier to scan, still looks the same.
And it seems that the ends gets cut off.
Since the building only have a size
of 130mm x 120mm, it should be scanned alright.

http://soliforum.com/i/?5YvTCcO.png
http://soliforum.com/i/?ju6Vfgs.png

]]> https://www.soliforum.com/user/16713/ 2017-04-26T11:07:18Z https://www.soliforum.com/post/134952/#p134952 <![CDATA[Re: deformation test]]> Sorry for the delay, but it got late here last night.
Different timezone : gmt+2.

I measured it all, and it was camera Y there was wrong, all the other
settings is good.
And its calibrated again.

And as you can see, the square isn't "square" wink

Here is last scan:

http://soliforum.com/i/?RBhgnuR.png
http://soliforum.com/i/?6TfeTMq.png

]]> https://www.soliforum.com/user/16713/ 2017-04-26T08:30:23Z https://www.soliforum.com/post/134946/#p134946 <![CDATA[Re: deformation test]]> The values for the camera settings should match the actual measurements.  Depending on how the scanner was built (printed parts, precut plywood, home made, etc), those values will differ.

Assuming one built the printed version correctly, their dimensions should be the same as the default settings, but then again, there are always variations, that's why it's important the values match the actual measurements.

]]> https://www.soliforum.com/user/1357/ 2017-04-25T20:32:03Z https://www.soliforum.com/post/134935/#p134935 <![CDATA[Re: deformation test]]> knowack wrote:

Camera Y, Right Laser X, and Left Laser X are all wrong. 

Take a look at post #19 of this thread for known good settings.


Here is a link to the exact post knowack is referring to.

http://www.soliforum.com/post/133437/#p133437

]]> https://www.soliforum.com/user/7731/ 2017-04-25T19:46:51Z https://www.soliforum.com/post/134930/#p134930 <![CDATA[Re: deformation test]]> Camera Y, Right Laser X, and Left Laser X are all wrong. 

Take a look at post #19 of this thread for known good settings.

]]> https://www.soliforum.com/user/4251/ 2017-04-25T19:26:19Z https://www.soliforum.com/post/134927/#p134927