<![CDATA[SoliForum - 3D Printing Community — Solidoodle 4 part fan]]> 2016-07-18T02:18:51Z PunBB https://www.soliforum.com/topic/15182/solidoodle-4-part-fan/ <![CDATA[Re: Solidoodle 4 part fan]]> I'd connect up a fan to those first and see if you can control it with the fan slider in RH first.  If it works than no need to flash the firmware.  If it doesn't work than the instructions in this link will get you started.  http://www.soliwiki.com/Updating_Solido … structions
They are out of date and some links will be broken.  Additional info on the PrintrBoard (that's what your board is) can be found here http://www.reprap.org/wiki/Printrboard# … Windows.29
I won't suggest flashing that particular board is fun or easy.  But it can be done if you take your time to research alternate methods following links from the sites I linked above.  Good luck.

]]> https://www.soliforum.com/user/2291/ 2016-07-18T02:18:51Z https://www.soliforum.com/post/125215/#p125215 <![CDATA[Re: Solidoodle 4 part fan]]> I see it, thank you! The ones on the right side of the last picture right? Also, could you explain flash firmware? I have not heard that term before and am also not familiar with programming. I am always a fan of figuring something out though smile

]]> https://www.soliforum.com/user/12806/ 2016-07-18T02:06:01Z https://www.soliforum.com/post/125213/#p125213 <![CDATA[Re: Solidoodle 4 part fan]]> If you look closely that board has unpopulated fan pins.  Just solder a couple pins on that spot or even a couple of wires.  Then you'll most likely need to flash firmware to activate that feature.  The version listed in the WIKI already has those pins enabled.  I have done this on several PrintrBoards and all have worked perfectly.

]]> https://www.soliforum.com/user/2291/ 2016-07-17T23:41:58Z https://www.soliforum.com/post/125206/#p125206 <![CDATA[Re: Solidoodle 4 part fan]]> http://soliforum.com/i/?o7QntOU.jpg

]]> https://www.soliforum.com/user/12806/ 2016-07-17T18:38:02Z https://www.soliforum.com/post/125205/#p125205 <![CDATA[Re: Solidoodle 4 part fan]]> Thank you for your response. I believe that it is standard, but here are some pics. I just meant that according to other threads, the newer solidoodles come with a board that solidoodle made.

http://soliforum.com/i/?Au8iOWy.jpg

http://soliforum.com/i/?BtiRcj6.jpg

http://soliforum.com/i/?Vm7Lzp9.jpg

These are the best pictures that I could get without disconnecting all the wires and possibly messing something up. Thank you for helping me smile

]]> https://www.soliforum.com/user/12806/ 2016-07-17T18:36:37Z https://www.soliforum.com/post/125204/#p125204 <![CDATA[Re: Solidoodle 4 part fan]]> You would need to supply us with detailed pics and information on this custom controller if it is not standard.

]]> https://www.soliforum.com/user/7731/ 2016-07-17T18:10:13Z https://www.soliforum.com/post/125202/#p125202 <![CDATA[Solidoodle 4 part fan]]> Hello everyone. I have a Solidoodle 4 that has the custom controller board. I am trying to figure out how I can wire a part cooling fan to the board so that I can control it from Repetier Host. Does this board have the built in ability to do that? Where on the board can I connect the fan?

]]> https://www.soliforum.com/user/12806/ 2016-07-17T17:30:08Z https://www.soliforum.com/post/125201/#p125201