<![CDATA[SoliForum - 3D Printing Community — PLA print melted layers]]> 2016-04-16T22:12:53Z PunBB https://www.soliforum.com/topic/14545/pla-print-melted-layers/ <![CDATA[Re: PLA print melted layers]]> Do what Kronikabuse said,,I to had the same problem with small objects,so just added more of them to print at the same time and works great.

]]> https://www.soliforum.com/user/14237/ 2016-04-16T22:12:53Z https://www.soliforum.com/post/121201/#p121201 <![CDATA[Re: PLA print melted layers]]> ^That
If you don't have the option of mounting a fan..
1) Remove any and all enclosures
2) Said desk fan and PID can help, but it is only a hail mary
3) Print a tall skirt as far away from the outer perimeter of the print as possible
4) With suggested 1-3 performed, slow your speed down slightly.

PLA needs longer times to cool, so keep this in mind first and foremost!

]]> https://www.soliforum.com/user/4188/ 2016-04-13T00:25:20Z https://www.soliforum.com/post/121002/#p121002 <![CDATA[Re: PLA print melted layers]]> With PLA, a fan is not optional, as you can see. If you don't want to wire one up to your machine, a desk fan blowing in the print area will work as a temporary solution, but you will likely have to re-run PID autotune with the fan blowing on everything.

]]> https://www.soliforum.com/user/7321/ 2016-04-12T22:57:15Z https://www.soliforum.com/post/120997/#p120997 <![CDATA[Re: PLA print melted layers]]> As suggested here before, a sacrificial column can do wonders.  I used Openscad to make a tall, skinny column and I place it distant to the printed object, just to give the layers some time to cool.

A layer fan can help a lot as well.  Of course, not my idea... another pearl from the community.

]]> https://www.soliforum.com/user/13355/ 2016-04-12T22:13:24Z https://www.soliforum.com/post/120993/#p120993 <![CDATA[Re: PLA print melted layers]]> You can try printing multiple parts like Kronik said to allow the previous layer to cool more... if your set on printing this one piece I would suggest using less infill as giving it some breathing area within the print would probably help it solidify. I usually print everything at 15% infill but you can try it at 20-30% and it should be solid enough... I would also leave the front and top door open to allow more cool air to enter the print area.

]]> https://www.soliforum.com/user/12717/ 2016-04-10T22:52:41Z https://www.soliforum.com/post/120890/#p120890 <![CDATA[Re: PLA print melted layers]]> this happens when the previous layer hasnt had enough time to cool before the next layer is printed. You can try putting a fan over the print area, or try printing multiple parts at one time to give time for cooling.

]]> https://www.soliforum.com/user/6797/ 2016-04-10T19:08:35Z https://www.soliforum.com/post/120876/#p120876 <![CDATA[PLA print melted layers]]> http://soliforum.com/i/?620lfuM.jpg

I am consistently getting melted layers when I try to print this chess figure at the following settings:

Temp: 190
Bed: 45
Layer: 0.2mm
Infill: 75%

Played with speeds, same results. Looks like as it progresses to the higher layers, they start melting and sinking.

Any advice?

]]> https://www.soliforum.com/user/14198/ 2016-04-10T18:34:55Z https://www.soliforum.com/post/120870/#p120870