My Duo "jams" the extruder motor strips the PLA filament but when I load it the filament comes out fine and there's no way to adjust the tension on the filament, ABS works fine.

EDIT=I had to re-flash Repetier with the duo options in config-h.
But I had to change the extruder from 2 to 1.  All is ok now thanks to Luc.

Here are the motors I got
http://www.banggood.com/JKM-42-Hybrid-S … 33548.html

http://www.banggood.com/MK8-Aluminum-Ex … 17150.html

I'm not using the extruder on the second motor. Anyone know which wires are for reverse?

did you disabled filament sensor ? if sensor is missing it will say no filament because of xyz sensor logic, so need to disable it in settings

I will try that as soon as I clear another filament jam 
Thanks luc   

No matter what program I use it want's me to load filament to the hot end that isn't there. So it won't print.
I've tried a new profile in simplify3D and Repetier host and it's still a no go.

Both see it as having 1 extruder but demand I load filament in to the one that's not there any more.
I've pulled the hot end plug from the motherboard=fail. Is there another plug\wire I need to disconnect?

Was about to order E3D V6 and the Titan Extruder. But there's no point if I can't get the test extruder working?

Thanks guys

I did flash it as a single extruder but with the newer motherboard. Would it be advisable to flash it again
but this time use 0 for the board instead of 1 ?

You can change it in firmware what you would do is home the z. ( make sure the e3d is not going to hit the bed and bind first) then use the manual controls in repetier to lower the bed until you know your print head can move over the print bed.
then carefully raise it  1mm to .1 mm until your just able to get the paper (or feeler gauge) to slip under it.

note the z height and then go change the end stop by the amount needed  in the firmware.

if your print head will bind before the z axis triggers  (depends on your modification)  then you need to modify the  end stop so it triggers at before the print head hits the bed then and then raise the bed slowly until your again able to slide the paper or feeler gauge under the print head.  note the z height and then change the z in the firmware.

Please note you don't have much room to make that go into the negative before the z end stop hits the top and binds. you do a have a few mm but not a lot so it needs to be close to begin with.

Thank you so much. My bed is now level and the flexi filament loads great.
BUT it won't un-load? the motor does a 1\4 of a turn then stops. Any body got any idea what I'm doing wrong?

I'm to old for all this 

edit=the hot end heats up ok.

edit 2= I can see a load distance setting but no Un-load one. As soon as the temperature reaches 230 if bleeps for a second
then goes back to the load\unload menu.

edit 3= It was a filament jam    need more coolinh on the hot end. At least I've learned something today 

note the z height and then go change the end stop by the amount needed  in the firmware.

if your print head will bind before the z axis triggers  (depends on your modification)  then you need to modify the  end stop so it triggers at before the print head hits the bed then and then raise the bed slowly until your again able to slide the paper or feeler gauge under the print head.  note the z height and then change the z in the firmware.

Please note you don't have much room to make that go into the negative before the z end stop hits the top and binds. you do a have a few mm but not a lot so it needs to be close to begin with.

Soryy about all this...dam newbies   

Ok.
Go in to settings then go down to position. Press right and you will see XYZ(something like that)
I didn't touch the first xyz but the z below them.

And don't for get to store the eprom each time. I have to load mine each time I turn it on?
Also I can't do a manual bed level from the maintenance as it's all over the place as it thinks it's a 1.0.

You need to reflash abd set it for what you have which is a 1.0 bow with only one fan and one extruder.

Thanks
Done that and it works 

Now I've just go to raise the small metal part that tells it when stop on the Z axis.
As my mod is 1 inch lower then the original hot end, and the bed is to high even with the nuts tight.

I'm only using 1 hot end(the right one) and I keep getting "heater decoupled" is it best to re-flash and pick
1 for DaVinci 1.0 (1Fan, 1 Extruder) instead of what I got now which is 3 for DaVinci 2.0 (2Fans, 2 Extruders)?

Thanks again

Open the firmware in Arduino and open the configuration.h tap. Then set the invert direction setting for the extruder to the opposite it is now. Or you could simply flip the connector so 1234 will be 4321. If the connector is keyed then just pull the wires from by unlocking the retaining clip in each one and physically move the wires to the reverse order.

This how it is now

// Inverting axis direction
850 #define INVERT_X_DIR true
851 #define INVERT_Y_DIR false
852 #define INVERT_Z_DIR true

Do I changed True on the top line to false and changed the second line to True?

https://github.com/luc-github/Repetier- … guration.h

Thank you for your help

edit=I haven't got a clue what to changed in the code