<![CDATA[SoliForum - 3D Printing Community — Solidoodle Motherboar Rev E Burn help me]]> 2016-08-01T13:47:31Z PunBB https://www.soliforum.com/topic/13789/solidoodle-motherboar-rev-e-burn-help-me/ <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> I have now Rumba, i bought it at 05/2016 and it arrived at 07/2016. Now I have all for repair my Solidoodle and i won't add auto-levelling. I will use the latest Firmware Marlin.
References: http://reprap.org/wiki/RUMBA

]]> https://www.soliforum.com/user/6143/ 2016-08-01T13:47:31Z https://www.soliforum.com/post/125709/#p125709 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> the A4988 stepper drivers are fine.
As wardjr said before the only one that would really benefit from a DRV8825 is E, but it is not a necessity.

I also do not care for the "auto-leveling" thing, and have not found any reason to add it to any of my machines (currently 4).
Taking the time to properly adjust things and removing any slop in the mechanical's will go much farther than auto leveling will. Not to mention that you STILL need to properly level your bed manually before using an auto-leveling system - so what is the point?

]]> https://www.soliforum.com/user/10399/ 2016-08-01T12:07:11Z https://www.soliforum.com/post/125707/#p125707 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> Hello, I have only A4988 drivers, is it a big problem?
I set it with max microstep (16).

]]> https://www.soliforum.com/user/6143/ 2016-08-01T09:20:26Z https://www.soliforum.com/post/125698/#p125698 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> You can add a g-code controlled nozzle fan and I alway mix up which pins.  Just try one and when it is always on that means it's the other pins wink
Auto level simply adds another un needed variable into a system with too many variables.  Using software to compensate for a poor mechanical platform should be a last resort.  It also adds unnecessary complexity to an already complex system.  Properly level your bed and use glass to create a flat surface.  Remove any slop or play and there is no need for auto level.

]]> https://www.soliforum.com/user/2291/ 2016-02-20T15:05:06Z https://www.soliforum.com/post/117031/#p117031 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> Other mods for my solidoodle 2 pro ? I have standard pieces (extruder...), but i see another motors and another extruder for improve the quality of this printer. Why do not you like auto level ? It is not accurate or it has other problem ?

PS: Can you help me for add another fan for PLA? in http://reprap.org/wiki/RUMBA#FAN0. Fan0 or Fan 1 for PLA? ithink FAN0 for extruder and FAN1 for pla but i don't know.

]]> https://www.soliforum.com/user/6143/ 2016-02-20T08:57:04Z https://www.soliforum.com/post/117024/#p117024 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> Yep how ever you want to do it a Rumba will handle it.  I personally do not like auto level but that's your choice.

]]> https://www.soliforum.com/user/2291/ 2016-02-20T02:57:42Z https://www.soliforum.com/post/117018/#p117018 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> Ok the better solution is Rumba board or similar with A4988 driver. then i put the firmware Marlin but the solidoodle firmware or another Marlin? Because in the forum i see the version of Marlin with function G29 (autolevel bed) so i can install it and then mount a M12 proximity sensor (http://www.soliforum.com/topic/13564/ha … ng-on-sd2/)

]]> https://www.soliforum.com/user/6143/ 2016-02-19T23:54:31Z https://www.soliforum.com/post/117009/#p117009 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> Find a Rumba or Azteeg X3 or buy a ramps 1.4 but only from a very reputable vendor.  There are a lot of garbage boards out there.

]]> https://www.soliforum.com/user/2291/ 2016-02-19T23:16:00Z https://www.soliforum.com/post/117007/#p117007 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> the best option because this work, in my opinion, is not easy.
But i prefer for my budget under 100€, because i have another project for this printer.When it works again , i would add a autoleveling bed (with proximity sensor)

]]> https://www.soliforum.com/user/6143/ 2016-02-19T23:09:28Z https://www.soliforum.com/post/117006/#p117006 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> This all depends on your budget.  Are you looking for the best option or an affordable replacement?

]]> https://www.soliforum.com/user/2291/ 2016-02-19T22:35:10Z https://www.soliforum.com/post/117003/#p117003 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> So i can buy this kit: http://www.ebay.it/itm/RAMPS-1-4-Contro … rmvSB=true

But i see another ramps 1.4: SainSmart 2 in 1 it's better because all in one, it is simple for power and connection.
What do you think about it?
Thank you very much for your time smile

]]> https://www.soliforum.com/user/6143/ 2016-02-19T22:15:56Z https://www.soliforum.com/post/116998/#p116998 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> DRV8825's are a better driver for E: as they will do 1/32 microsteps.  They aren't needed for X,y, or z as the extra steps doesn't noticeably improve print quality.

]]> https://www.soliforum.com/user/2291/ 2016-02-19T21:35:47Z https://www.soliforum.com/post/116991/#p116991 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> I read this: http://reprap.org/wiki/RAMPS_1.4#Stepper_Driver_Boards
driver better is DRV8825.

]]> https://www.soliforum.com/user/6143/ 2016-02-19T21:12:25Z https://www.soliforum.com/post/116986/#p116986 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> this for example RAMPS 1.4
http://www.ebay.it/itm/RAMPS-1-4-Contro … SwsB9WA9rO

]]> https://www.soliforum.com/user/6143/ 2016-02-19T18:22:20Z https://www.soliforum.com/post/116960/#p116960 <![CDATA[Re: Solidoodle Motherboar Rev E Burn help me]]> post a link of what you are looking at and we can tell you if it will work.

]]> https://www.soliforum.com/user/2291/ 2016-02-19T17:30:36Z https://www.soliforum.com/post/116957/#p116957