<![CDATA[SoliForum - 3D Printing Community — Announcing PRINTiTindustries.com]]> 2016-03-18T02:57:14Z PunBB https://www.soliforum.com/topic/13778/announcing-printitindustriescom/ <![CDATA[Re: Announcing PRINTiTindustries.com]]> Huge thumbs up to printit guys! Got myself a full set of printable rplacement parts, and i'm rolling with ease!

]]> https://www.soliforum.com/user/10313/ 2016-03-18T02:57:14Z https://www.soliforum.com/post/119488/#p119488 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Congrats....  I wish you guys all the best.

]]> https://www.soliforum.com/user/7495/ 2016-03-01T00:31:47Z https://www.soliforum.com/post/118379/#p118379 <![CDATA[Re: Announcing PRINTiTindustries.com]]> All announcements for newly stocked items will now be made in the BST area of the forum to allow any further discussion of PRINTiT Industries to take place here.

We again would like to thank everyone for their support and business smile

]]> https://www.soliforum.com/user/4188/ 2016-02-29T22:34:53Z https://www.soliforum.com/post/118367/#p118367 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Several accessories for electronics have been added.
This includes, to name a few:
*Stepper Drivers- Both A4988 and DRV8825
*Raspberry Pi B+
*Male Headers
*Rocker Switches
*Pre-Crimped Wires

Check out our Electronics Section for the full updated listing.

]]> https://www.soliforum.com/user/4188/ 2016-02-23T17:51:13Z https://www.soliforum.com/post/117599/#p117599 <![CDATA[Re: Announcing PRINTiTindustries.com]]> clones maybe dont pre crimp like from ebay/amazon etc. thats just 1 of many short cuts they take plus not made in USA. thats why this venture is so much better. even if a bit more money than the clones. 'ounce of prevention = pound of cure'

]]> https://www.soliforum.com/user/795/ 2016-02-21T03:55:25Z https://www.soliforum.com/post/117089/#p117089 <![CDATA[Re: Announcing PRINTiTindustries.com]]> All good news, guys. I think you're making some smart moves. When is your $500 error-free, SLA printer coming out? And that $500 high-capacity desktop injection molding machine?

]]> https://www.soliforum.com/user/2447/ 2016-02-20T16:52:55Z https://www.soliforum.com/post/117039/#p117039 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Yep, we sure do! The only thing end-users have to figure out is how they will connect the heater to their board. Unfortunately this is still far from standardized and likely never will be, so we leave it up to you.

]]> https://www.soliforum.com/user/7321/ 2016-02-19T22:42:22Z https://www.soliforum.com/post/117004/#p117004 <![CDATA[Re: Announcing PRINTiTindustries.com]]> mdrVB6 wrote:

Is that a recent change that E3D made?  Or is that just for the ones from this site?  Got both my E3D's a while ago and had to crimp them myself.

As long as I can remember v6 hotends have always had pre terminated (on the controller board side) thermistor cables. Yes, you have to use the ferrules to connect the thermistor to the thermistor cable, but it stands to reason that a company offering preassembled hotends would be connecting the thermistor cable to the thermistor for you.

]]> https://www.soliforum.com/user/221/ 2016-02-19T22:17:57Z https://www.soliforum.com/post/116999/#p116999 <![CDATA[Re: Announcing PRINTiTindustries.com]]> mdrVB6 wrote:

  With a thermistor short, its pretty hard to tell whether it got shipped out with a little bit of frayed sleeving, or if it became like that during installation.

All hotends we sell are fully assembled complete with heat tightening. During this final step, thermistors are tested, then carefully packaged once cooled.

]]> https://www.soliforum.com/user/4188/ 2016-02-19T22:06:14Z https://www.soliforum.com/post/116997/#p116997 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Oh, no! What a bunch of crooks!

Congratulation on the new venture, guys. With your expertise and good hearts, I'm sure you'll do well. You've sure helped me.

]]> https://www.soliforum.com/user/2447/ 2016-02-19T21:52:44Z https://www.soliforum.com/post/116993/#p116993 <![CDATA[Re: Announcing PRINTiTindustries.com]]> If ordered as a pre assembled unit from www.printitindustries.com it comes fully assembled.  That means the wires are already crimped and just need to be plugged into the board.  The ones you ordered were not pre assembled units.

]]> https://www.soliforum.com/user/2291/ 2016-02-19T21:32:38Z https://www.soliforum.com/post/116990/#p116990 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Is that a recent change that E3D made?  Or is that just for the ones from this site?  Got both my E3D's a while ago and had to crimp them myself.

]]> https://www.soliforum.com/user/4377/ 2016-02-19T21:25:52Z https://www.soliforum.com/post/116989/#p116989 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Thermistor cables are pre-terminated from E3D with 0.1" pin headers, there's no need for the end user to crimp anything.

Also I've assembled E3D hotends for customers a bit here and there as a favor, no complaints so far.

]]> https://www.soliforum.com/user/221/ 2016-02-19T21:24:03Z https://www.soliforum.com/post/116988/#p116988 <![CDATA[Re: Announcing PRINTiTindustries.com]]> Very interesting and I hope you guys are able to help some people while also turning a profit for your time.  Personally, I would be pretty reluctant to sell someone a pre-assembled E3D hot end because of the better than not chance that they mess it up while installing it and then blame you.  For example, since you are not including wiring terminations, there's a pretty good chance of someone man handling it while attempting to crimp a connector onto the thermistor and causing a short due to unrestrained wires moving around.  With a thermistor short, its pretty hard to tell whether it got shipped out with a little bit of frayed sleeving, or if it became like that during installation.  I believe you guys would ship well assembled ones, but I'm surprised you are willing to take the risk for what could become a customer service nightmare.

]]> https://www.soliforum.com/user/4377/ 2016-02-19T21:15:54Z https://www.soliforum.com/post/116987/#p116987 <![CDATA[Re: Announcing PRINTiTindustries.com]]> We all thank you for your kind words and support.
We just added a Coming Soon section. At this date and time, items in that category are expected in within the next few days.

Still more to come...

]]> https://www.soliforum.com/user/4188/ 2016-02-19T20:07:01Z https://www.soliforum.com/post/116974/#p116974