<?xml version="1.0" encoding="utf-8"?>
<feed xmlns="http://www.w3.org/2005/Atom">
	<title type="html"><![CDATA[SoliForum - 3D Printing Community — Firmware?]]></title>
	<link rel="self" href="https://www.soliforum.com/feed/atom/topic/13734/" />
	<updated>2016-02-21T03:02:53Z</updated>
	<generator>PunBB</generator>
	<id>https://www.soliforum.com/topic/13734/firmware/</id>
		<entry>
			<title type="html"><![CDATA[Re: Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/117082/#p117082" />
			<content type="html"><![CDATA[<p>The changes in the new formware are: activiating the bottom Z endstop, and new commands to adjust the Z-probe XY offset and the area that is Z-probed. </p><p>YMMV, but these weren&#039;t quite compelling enough to me to give my Press an entirely new opportunity to fail by upgrading. (Although I do run into the non-working Z-stop thing on rare occasion. Literally. <img src="https://www.soliforum.com/img/smilies/smile.png" width="15" height="15" alt="smile" /> )</p>]]></content>
			<author>
				<name><![CDATA[trayracing]]></name>
				<uri>https://www.soliforum.com/user/7353/</uri>
			</author>
			<updated>2016-02-21T03:02:53Z</updated>
			<id>https://www.soliforum.com/post/117082/#p117082</id>
		</entry>
		<entry>
			<title type="html"><![CDATA[Re: Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/116660/#p116660" />
			<content type="html"><![CDATA[<p>Hmm, I stand corrected.&nbsp; Maybe &quot;solidoodle&quot; was only in the URL of the post so it didn&#039;t get returned.</p><p>Anyhow, it&#039;s a lousy situation with Solidoodle, and I guess this might be the signal that they are at the last stages - or maybe it&#039;s just an inadvertent mishap on their accounting department?! &lt;not holding breath&gt;</p>]]></content>
			<author>
				<name><![CDATA[fredhag]]></name>
				<uri>https://www.soliforum.com/user/97/</uri>
			</author>
			<updated>2016-02-16T17:17:14Z</updated>
			<id>https://www.soliforum.com/post/116660/#p116660</id>
		</entry>
		<entry>
			<title type="html"><![CDATA[Re: Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/116639/#p116639" />
			<content type="html"><![CDATA[<p><a href="http://www.soliforum.com/post/115492/#p115492">http://www.soliforum.com/post/115492/#p115492</a></p>]]></content>
			<author>
				<name><![CDATA[MacGyverX]]></name>
				<uri>https://www.soliforum.com/user/4348/</uri>
			</author>
			<updated>2016-02-16T14:07:58Z</updated>
			<id>https://www.soliforum.com/post/116639/#p116639</id>
		</entry>
		<entry>
			<title type="html"><![CDATA[Re: Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/116629/#p116629" />
			<content type="html"><![CDATA[<p>I searched soliforum for &quot;solidoodle support&quot; and only found this post.&nbsp; I&#039;m&nbsp; surprised there hasn&#039;t been any chatter here about the Solidoodle support site going down (expiring with Zendesk).&nbsp; I noticed as I was trying to download the Mac version of Solidoodle&#039;s settings for Repetier (luckily, I had downloaded it and kept it on another computer).</p>]]></content>
			<author>
				<name><![CDATA[fredhag]]></name>
				<uri>https://www.soliforum.com/user/97/</uri>
			</author>
			<updated>2016-02-16T12:43:12Z</updated>
			<id>https://www.soliforum.com/post/116629/#p116629</id>
		</entry>
		<entry>
			<title type="html"><![CDATA[Re: Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/116593/#p116593" />
			<content type="html"><![CDATA[<p>If your printer is working up to your expectations there will be no benefit to updating your firmware.&nbsp; Unless you are planning on modifying or upgrading to an E3d hot end, leave well enough alone.</p>]]></content>
			<author>
				<name><![CDATA[wardjr]]></name>
				<uri>https://www.soliforum.com/user/2291/</uri>
			</author>
			<updated>2016-02-15T22:55:03Z</updated>
			<id>https://www.soliforum.com/post/116593/#p116593</id>
		</entry>
		<entry>
			<title type="html"><![CDATA[Firmware?]]></title>
			<link rel="alternate" href="https://www.soliforum.com/post/116570/#p116570" />
			<content type="html"><![CDATA[<p>I haven&#039;t updated my firmware for my press. I am concerned because Solidoodle support, website etc... is down... Should I try to update it? It seems to be running ok? </p><p>Anna Lenhart Murray</p>]]></content>
			<author>
				<name><![CDATA[annalenhartmurray]]></name>
				<uri>https://www.soliforum.com/user/7665/</uri>
			</author>
			<updated>2016-02-15T18:59:19Z</updated>
			<id>https://www.soliforum.com/post/116570/#p116570</id>
		</entry>
</feed>
